i need the answer quickly choose the correct answerMcq: the maximum shar stress in contact between twosteel spheres pressed together lies?1-at the contact surface2-at the point of maximum principal stress3-under the contact surface

Ans: 3 is correct. Under the contact surface

Answered: Mcq: the maximum shar stress in contact…

Mcq: the maximum shar stress in contact between steel spheres pressed together lies? 1-at the contact surface 2-at the point of maximum principal stress 3-under the contact surface

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Related questions

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. 300…

A: (a) The stress in the rod AB: 129 MPa (b) The diameter of pin at C: 12 mm

Q: Find the resultant couple moment (in N.M) at point O. 500 N 300 N 200 N m 2 m 2 m

Q: 5.) Does a refrigerator full of food consume more power if the room temperature is 200C than if it…

Q: A solid cylindrical bar conducts heat at a rate of 25 W from a hot to a cold reservoir under steady…

Q: What is the magnitude of the force on an inclined gate shown? The tank contains water and is…

Q: Thermodynamics can describe the * O Fluid flow O vibration of the body O Force O The Kinentic and…

A: Thermodynamics is the branch of science that deals with energy transfer and its effect on the…

Q: B- Explain why temperatures at high altitudes? (" we use air-conditioning systems for air planes…

A: We use air-conditioning systems are used for airplanes despite the low ambient temperature at high…

Q: A solid 1.500-in.-diameter steel shaft is subjected to torques Tg = 185 Ib-ft and Tp= 150 lb-ft,…

A: Given: Torque applied on pulley B→TB=185 lbft (inside the shaft) Torque applied on pulley…

Q: Consider a cylindrical rotating machine where the rotor rotates at a rate of 900 rev/min. Air enters…

Q: 028- The value of e-(In+1)n is a) (-1)" e--1 b) (-1)"e" c) (-1)" e-n+1 d) (-1)" e-"

Q: Q3/ For the figure shown below, .compute the centroid of the figure 6m 3m 4.5 m 3m

A: find the centroid of the shaded area.

Q: A Camot cycle uses nitrogen as the working substance. The heat supplied is 54 kJ. The temperature of…

Q: Two kilograms of an ideal gas at 700 kPa with an initial volume of 0.25 m3 expand adiabatically to a…

A: find the work done during adiabatic process.

Q: I want the third dro 106 50 16 40 20 32 16 16 59 62 3L

Q: Lukewarm water at 60 degree c in a storage tank is being pumped at 300 L/min from the tank. The…

Q: A bubble (assuming perfectly spherical) was released from a depth of 120m in the body of water by a…

A: Given data A bubble forms at a depth of 120 mAssuming the temperature remains constantm we have to…

Q: Consider a 2-m-wide 1.5-m-high wood-framed window with 3-mm-thick single-panel glass covering 85…

Q: 3. A 2-mm-diameter and 10-m-long electric wire is tightly wrapped with a 1-mm-thick plastic cover…

Q: A 600 mm steel pulley transmits 50 kW at 900 rpm. The arc of contact between the belt and pulley is…

Q: Flow Rate: 5305 Lis ORuler Speed Presure Units O Metrie O English 101.302 kPa Friction OFlux meter…

Q: )واجب بتی .H.W F3-5. If the mass of cylinder C is 40 kg, determine the mass of cylinder A in order…

Q: 7,(1 – n), 5.10 In a laminar boundary layer, the shear stress distribution is given as t= T where n…

Q: Q2/ Determine the forces at the pin joint ? (F) and the roller support (G) 30KN 20 KN 2m BY 2m D 2m…

Q: The mass of air in a room 3X 4 X 20 m is known to be 200 kg. Determine the density: O p=1000 kg/m3 O…

Q: 1. Draw a graph relating dilatant and thixiotropic fluids in terms of torque and viscosity versus…

A: In dilatent fluids, with increase in the velocity, torque and viscosity increases. And for…

Q: A Carnot heat engine operates between 840oC and 5oC and rejects 580 kJ/min of heat to the low…

A: Given Maximum temperature, T1 = 840oC = 1113 K Minimum temperature, T2 = 5oC = 278 K…

Q: Determine the force P needed to hold the 100-kg block in equilibrium.

A: To find Force P

Q: In a reheat Rankine cycle, the steam throttled condition is 8 MPa and 480°C. The steam is then…

A: Given data Steam at throttled condition = 8 MPa and 480°C Reheat pressure = 2 MPa Reheat conditions…

Q: 7.52 PLUS Neglecting head losses, determine what power the pump must deliver to produce the flow as…

Q: A cylinder vessel filled with water with a 2m diameter and 5m high. It was rotated with uniform…

Q: w agua 1.00m

Q: · Give the terminology for each numeral question mark mentioned in the Figure (2) below:- PINION 1-7…

Q: The displacement of a particle is given by s 2t3 - 30f2 + 100t – 50, where s is in feet and t is in…

Q: If a body looses half of its velocity on penetrating 3 cm in a wooden block, then how much will it…

Q: B/The three components of velocity in the flow field are given below. Determine an expression for…

A: u= x2 + y2 + z2v= xy + yz + z2w= -3xz - z22 + 4

Q: 2. Show which kind of the double-pipe heat exchanger exchange more heat between the hot and cold…

Q: Q2/ Determine the forces at the pin joint (F) and the roller support (G) ? 20 KN 30KN 2m By 2m D 2m…

A: find the reactions at the support at G and F.

Q: Sketch multi-views (front, top and right views) of the objects. The front view is from bottom-left…

Q: A two branch duct system of circular duct is shown below. The fittings have the following equivalent…

Q: Q3/ For the figure shown below, compute the centroid of the figure. 6m 3m 4.5 m

Q: Q6:- The firing order in a 6-cylinder, 4-stroke, in-line engine is 142635. The piston stroke is 100…

Q: f(h,p,D,V, µ, Cp, k) k = thermal conductivity (W/m°C) h = convective heat transfer coefficient…

Q: 4. A bus travels the 100 miles between A and B at 50 mi/h and then another 100 miles between B and C…

A: A bus travels the 100 miles between A and B at 50 mi/h and then another 100 miles between B and Cat…

Q: 2/4 The velocity of a particle along the s-axis is given by v = 5s32, where s is in millimeters and…

Q: 4. A rigid tank initially contains 5kg of saturated vapor steam at 150°C. Heat transfer is done…

Q: A particle travels along a path where y = 8x3. The particle increases height with y = 27t3 where t…

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

Q: A closed tank contains 0.6 m of mercury, 1.6 m of water, 2.7 m of oil of specific gravity 0.9 and…

Q: A tripod supports the load W as shown in the figure. Determine the maximum load "W" (in pounds),…

A: Given Maximum leg limited = 87 lbs To find Magnitude of W

Q: A vertical semi-circular area of radius r is submerged in a liquid with its diameter in the liquid…

A: The position of center of pressure from liquid surface is (3*pi*r/16).

Question

i need the answer quickly

choose the correct answer
Mcq: the maximum shar stress in contact between two
steel spheres pressed together lies?
1-at the contact surface
2-at the point of maximum principal stress
3-under the contact surface

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar. Express your answer in MPa.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3. Determine the average compressive stress acting atpoints A and B.
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.
An 8 mm thick cylindrical steel tank has an outside diameter of 600 mm and a length of 3 m. (a) when the tank is filled with water, determine the circumferential stress. (b) determine the longitudinal stress at the bottom of the when it is filled with water. (c) if the stress is limited to 5 mpa, what is the maximum height of water to which the tank maybe filled.
What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a load of 1000 N? Express your answer in N/m2, Mpa, and psi.
A 4-ft diameter spherical tank is subjected to an internal pressure of 12 psf. If the wall thickness is 0.38", determine the tangential stress of the wall in psi.
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder
The suspender rod is supported at its end by a fixed-connected circular diskas shown in Fig. 1–26a. If the rod passes through a 40-mm-diameter hole,determine the minimum required diameter of the rod and the minimumthickness of the disk needed to support the 20-kN load. The allowablenormal stress for the rod is sallow = 60 MPa, and the allowable shear stressfor the disk is tallow = 35 MPa.
A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The cylinder is designed to store fluid at 80 MPa:(a) Determine the external pressure necessary to bring the hoop stress at the outer wall of the cylinder to zero. (b) Draw the variations of the hoop and radial stress across the thickness of the wall. Indicate the stress values at both inner and outer radii.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
No Normal stress acts on the neutral axis. Is it true or false? How?