Mechanical system consists of: body 1 of mass m=m; body 3 - two-stage disk of mass m;=4m, radii r and R=2r, and radius of inertia i, toward horizontal axes passing through its center; both bodies 4 - equal horizontal springs each of coe- fficient of elasticity c. An ideal cord 2 connects body 1 and body 3. Disk 3 moves by its bigger drum on a fixed horizontal plane without sliding. At the initial moment system is turned out of its equilibrium by small shifting of magnitude x, of point

Mechanical system consists of: body 1 of mass m=m; body 3 - two-stage disk of mass m;=4m, radii r and R=2r, and radius of inertia i, toward horizontal axes passing through its center; both bodies 4 - equal horizontal springs each of coe- fficient of elasticity c. An ideal cord 2 connects body 1 and body 3. Disk 3 moves by its bigger drum on a fixed horizontal plane without sliding. At the initial moment system is turned out of its equilibrium by small shifting of magnitude x, of point

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.2P: Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the...

See similar textbooks

Similar questions

A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
The shaft, bearing two unbalanced masses, rotates at a constant speed of ω = 20 r/s. In the case of balancing in the DI and DII planes, find the balancing values (kg.mm) and their positions.
A caravan weighs 28 kN. It has a wheel base of 2 m, track width 1m and height ofC.G. 300 mm above the ground level and lies midway between the front andrear axle. The engine flywheel rotates at 2950 rpm clockwise when viewed from thefront. The moment of inertia of the flywheel is 4 kg-m 2 and moment of inertia ofeach wheel is 3 kg-m 2 . Find the reactions between the wheels and the ground whenthe car takes a curve of 15 m radius towards right at 30 km/h, taking intoconsideration the gyroscopic and the centrifugal effects. Each wheel radius is 400 mm.
An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at 200 km per hour. The rotary engine and the propeller of the plane has a mass of 400 kg with a radius of gyration of 300 mm. The engine runs at 2400 r.p.m. clockwise, when viewed from the rear. Find the gyroscopic couple on the aircraft and state its effect on it. What will be the effect, if the aeroplane turns to its right instead of to the left ?
Consider the system formed by the tapered-type flywheel and the 100-kg block shown in the figure below. The block is suspended from an inextensible cord that is wrapped around a pulley of 300-mm radius rigidly attached to the flywheel. The pulley and the flywheel have a combined mass moment of inertia about its center of IT= 0.45 kg. m2. At the instant shown, the velocity of the block is 2 m/s directed downward. If the bearing at O is poorly lubricated and that the bearing friction is equivalent to a couple moment M of magnitude 80 N.m, determine the velocity of the block after it has moved 1 mdownward. Include FBD
Determine the additional mass required for stable equilibrium. Meter stick: xcm = 50.0 cm, m = 150.0 g. Hanger clamp: x = +0.0 cm, m = 16.5 g. (see the figure below)
A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating masses of the engine have an angular speed of 100 rad/s in clockwise direction when viewed from the front of the car The combined moment of inertia of the rotating masses is 10 kg-m².what is the magnitude of the gyroscopic moment in (N-m)?
A uniform disc of 25-kg mass and 500-mm diameter is mounted on a shaft. The plane of the disc is not perfectly at right angles to the axis of the shaft but has an error of 2.5 deree. Determine the gyroscopic couple acting on the bearing if the shaft rotates at 1000 rpm.
A rigid body is made of three identical thin rods, each of mass m and length L= 0.6 m,attached together in the form of an H. The body is allowed to fall from the horizontalposition, rotating around one of the legs of the H.a) What is the rotational inertia of the H, in terms of m and L?b) What will be the angular speed of the H when it is oriented vertically?
The cranks and connecting rods of a four cylinder in-line engine running at 2000 rpm are 60mm and 240mm each respectively. The cylinders are spaced 150 mm apart. If the cylinders are numbered 1 to 4 in sequence from one end, the cranks appear at intervals of 90º in an end view in the order 1-4-2-3.The reciprocating mass for each cylinder is 15 kg. Determine (i) unbalanced primary and secondary forces, (ii) unbalanced primary and secondary couples with reference to central plane of the engine
SAMPLE PROBLEM Determine the equivalent of the system using the angular motion of the i Show the complete solution. upper bar. Rigid massless link Identical slender bars of mass m, length L
The beam, uniform in mass, M = 47.6 kg and length L = 10.2 m, hangs by a cable supported at point B, and rotates without friction around point A. On the end far of the beam, an object of mass m = 24.3 kg is hanging. The beam is making an angle of θ = 30.9° at point A with respect to the + x-axis. The cable makes an angle φ = 21.1° with respect to the - x-axis at B. Assume ψ = θ + φ. a. Enter an expression for the lever arm for the weight of the beam, lB, about the point A. b. Find an expression for the lever arm for the weight of the mass, lm. c. Write an expression for the magnitude of the torque about point A created by the tension T. Give your answer in terms of the tension T and the other given parameters and trigonometric functions. d. What is the magnitude, in newtons, of the tension in the cable? e. Enter an expression the horizontal component of the force, Sx, that the wall exerts on the beam at point A in terms of the tension T, given parameters, and variables…