Mechanical system: mass-spring-damping system. Force f(t) and displacement xo(t) are input variable and output variable. Please give its differential equations, make Laplace transform and draw its block diagrams. ( x(1) KS BL m2 K2

Mechanical system: mass-spring-damping system. Force f(t) and displacement xo(t) are input variable and output variable. Please give its differential equations, make Laplace transform and draw its block diagrams. ( x(1) KS BL m2 K2

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.6P

See similar textbooks

Similar questions

laplace transform
The transfer function of a system is the ratio between _________________ and ____________ in Laplace transform. a. Output and Input b. Input and Output c. Input and Feedback d. Output and Feedback
Derive the governing differential equation for each system with the chosen generalized coordinate. SEE THE IMAGE BELOW Answers: 1. GDE: (5/2) mẍ + (5/4) kx = 0 2. GDE: (7/48) mL² ϴ [note: theta symbol has two dots above) + (3/8) cL² ϴ [ note: theta symbol has one dot above] + 5 kL² ϴ = 0
Consider the thermocouple properties you found in the question "Temperature of a thermocouple (1/3)" If the thermocouple is initially outside of the bath at room temperature (20 °C), what is the maximum temperature it will register if it's instantaneously inserted into the batch (55 °C) for 18 seconds and then removed? Use an inverse Laplace transform to find the solution. a. 32.68 °C b. 44.97 °C c. 64.97 °C d. 12.68 °C
A Block diagram of a feedback control system is shown in Figure Q3. Using the Block Diagram Reduction Method, solve for the output Y(s) when:(i) Input D(s) = 0,(ii) Input R(s) = 0,(iii) Input R(s) and D(s) are both applied (i.e., R(s) ≠ 0 , D(s) ≠ 0).
A vibrating spring-mass system has the feedback control system shown in Fig Q3 below. (figure attached as image ACT)If K = 12.25 determine:6.1 the transfer function ; (3)6.2 the characteristic equation with a impulse input; (1)6.3 the un-damped natural frequency of the system; (2)6.4 the damping ratio; (2)6.5 the damped natural frequency; (2)6.6 the maximum percentage overshoot; (2)6.7 the peak time; (1)6.8 the settling time for the response within 2%. (2)
A system has the following characteristic equation: s+ s+ 3s+ 2s + 2 = 0 Using the Routh-Hurwitz method, checka. How many roots are to the right of the imaginary axis?b. Is the system stable?.
Q(s) = S5 + 2S4 + 2S3 + 4S2 + 11S + 10 = 0 i). Identify the stability of the system using Routh Hurwitz Algorithm. (ii). Comment about the Roots location.
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): 1. What is the order of this system?
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): A. Use Laplace transform of the differential equation to determine the transfer function of the system.
The block diagram given below; A) Reduce it B) G1(s)=2/s ; G2(s)=1/4s+2 ; G3(s)=4 ;H(s)=0.5 Given the values of the system; find the time constant, its natural frequency and damping rate and explain what kind of dynamic behavior it exhibits accordingly. C)Find the poles and zeros of the system according to the values in (B).Is the system stable? Find the unit step response (Inverse Laplace).
Sketch the level response for a bathtub with cross-sectional area of 8 ft 2 as a function of time for the following sequence of events; assume an initial level of 0.5 ft with the drain open. The inflow and outflow are initially equal to2ft3/min.(a)The drain is suddenly closed, and the inflow remains con-stant for 3 min (0≤t≤3).(b)The drain is opened for 15 min; assume a time constant in a linear transfer function of 3 min, so a steady state is essentially reached (3≤t≤18) (c)The inflow rate is doubled for 6 min (18≤t≤24).(d)The inflow rate is returned to its original value for 16 min(24≤t≤40).