Mechanics of Deformable Bodies80 N200 mm300 mmBThe pipe shown in the figure has an inner diameter of80 mm and an outer diameter of 100 mm. If its end istightened against the support at A using a torquewrench at B, determine the shear stress developed inthe material at the inner and outer walls along thecentral portion of the pipe when the 80-N forces areapplied to the wrench.с80 N

Solution-The given data,Innerdiameter=80mmOuter diameter=100mm80N forcesTo Determine,The shear…

Answered: Mechanics of Deformable Bodies 80 N 200…

Mechanics of Deformable Bodies 80 N 200 mm 300 mm B The pipe shown in the figure has an inner diameter of 80 mm and an outer diameter of 100 mm. If its end is C 80 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Proposed exercise N ° 01 Find the angle of torsion of the free end with respect to the fixed end of the system in the figure. The material is steel and the dimensions are in cm. Proposed exercise N ° 2 Find the length that a hollow steel bar of D = 1.5cm and d = 0.5cm in diameters must have for its ends to rotate 30 ° relative to each other. An allowable shear stress of 713.8 kg / cm2 must not be exceeded, and G = 8.1573x105 kg / cm2
the figure below has the following data: F1=1.7kN, F2=0.8kN, F3=0.58kN, a=1.33 meters, 36 degrees, belta=47 degrees. determine the reaction at b in kN. support A is a roller and Support B is hinge.
Figure Q2 shows a reinforced concrete platform with a cantilever slab and wall at the edge of slab. The brick wall is seated on the edge of cantilever slab is 3.2 m high. Given: All slab thickness = 150 mm All beams = 250 mm × 600 mm Concrete unit weight = 25 kN/m3Weight of brickwall = 2.6 kN/m2Finishes = 1.5 kN/m2Variable action = 5 kN/m2 Determine the characteristic permanent action (gk in kN/m) and variable action (qk in kN/m) acting on Beam B/1-2.
A hollow steel shaft 2660mm long is to be designed to transmit a torque of 24809kJ. Theshear modulus of elasticity, G = 82,740 GPa for steel. The total angle of twist of the lengthof the shaft is must not exceed 6 degrees. And the shear stress in the shaft must notexceed 110.32 MPa. What would be the ratio of the outside diameter to inside diameter?
length=7m height=250mm UDL on the beam=38.5KN/M d=812mm Mass of the beam=65.9kg/m a. Consider design loads( udl+self weight) b. Calculate and draw the Bending Moment Diagram (BDM).What is the value of the maximum bending moment? c. Calculate and draw the Shear Force Diagram (SFD).What is the value of the maximum shear force? d. Using the table, calculate the maximumdeflection of the beam.
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
From the given figure below and its properties, calculate the stress at the top where the maximum moment is located. (MPa) Properties: Beam width = 207 mmBeam height = 386 mmWLL = 12.48 kN/mWDL = 15.26 kN/mSpan of the beam = 8 mPrestressing force = 293 kNeccentricity = 135 mm
A solid constant-diameter circular shaft is subjected to the torques of TA = 460 lb·ft, TB = 1000 lb·ft, TC = 880 lb·ft, and TD = 340 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7200 psi, what is the minimum acceptable diameter for the shaft?
The system lamp has a mass M and is supported by the six strings shown. The length of the chords and the horizontal distance ED are constant, point E remains fixed but the vertical distance ED can vary. a) If in the position shown the chord BC is horizontal, calculate the angle ? to maintain equilibrium, consider the mass M = 10 kg. b) Explain what happens to the magnitude of the stresses when point D moves.
The solid steel shaft carries the torques T1= 1200 Nm and T2=750 N m. Using L1=L2=2.5 m and G = 83 GPa, determine: a. draw a diagram using a double headed arrows showing the torque in each segment b. determine the shear stresses in each segment and the angle of rotation of the free end if the diameter is 100 mm. c. the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 4^0.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
A hollow shaft shown with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 75 kN and torques TB = 16 kN-m and TC = 7 kN-m. 14. Calculate the polar moment of inertia of the section in mm4.1 15. Calculate the absolute value of the internal torque at H in kN.m. 16. Calculate the torsional shear stress at H in MPa. 17. Calculate the absolute value of the minor principal stress at point H in MPa. 18. Calculate the absolute value of the major principal stress at point H in MPa. 19. Calculate the absolute value of the maximum shear stress at point H in MPa. 20. Calculate the orientation of the principal axes in degrees. Kindly answer all numbers with complete solution