Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has the following properties: R = 90 mm, n =4 turns, G = 70 GPa, d = 30 mm, and Tallow 105 MPa while Member AC has the following properties: L =2, A= 500 mm2, E = 200 GPa, and oallow= 30 MPa. Determine the maximum safe value of W (in N). Use simplified formula for the helical %3D %3D %3D spring. A 60°

Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has the following properties: R = 90 mm, n =4 turns, G = 70 GPa, d = 30 mm, and Tallow 105 MPa while Member AC has the following properties: L =2, A= 500 mm2, E = 200 GPa, and oallow= 30 MPa. Determine the maximum safe value of W (in N). Use simplified formula for the helical %3D %3D %3D spring. A 60°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the following if f'c=21 MPa and f(subscript)y= 415 MPa a.) balanced steel ratio b.) maximum steel ratio c.) nominal moment capacity in kn-m d.) ultimate moment capacity
Determine the diameter of each steel wire connected to the rigid members AB and DC. The members were originally horizontal. After the application of the 300 kN load, a vertical displacement of 1cm occurred at the point of application, let us say point I. Use E – 200 GPa.
NOTE: Wp= 'ac' lb = 33 lb. In other words the weight of the pipe is 33 lb. a) If the bolt exerts a force of 50 lb on the pipe in the direction shown, compute the force (lb) that the smooth contacts (i) at A exerts on the pipe. (ii) at B exerts on the pipe. b) Determine the maximum weight of the pipe (lb) that the vise can hold if the magnitude of the forces at A and B are equal.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
Consider a column bean under compression. A load P is applied at the upper end.Both ends have pinned boundary conditions. As you answer the following questions, you must explain each step, so you can show that you understand each step. You must also be concise and very brief.a.What is the critical load for this system. b.Assume that you now add a pinned supportis located a third of the way from the top of the column,and athird from the bottom of the column. These pinned supports prevent the column from laterally translating at the points of support. What is the new critical load of this system? Solve this problem in two very simple ways
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.50 in. and a wall thickness of 0.201 in. is fastened to a solid 2.00-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=19 kips, Q=13 kips, L1=7 ft, L2=9 ft, and L3=9 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
What is the internal force in member AB? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , CSHOW SOLUTIONS
Aload of P= 80 kN is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 95 GPa] rods, and a solid steel [E = 238 GPa] rod, as shown. The bronze rods (1) each have a diameter of 20 mm and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 24 mm. All bars are unstressed before the load P is applied: however, there is a 0.9-mm clearance in the bolted connection at B. Assume L1 = 2.6 m and L2= 1.3 m. Determine: (a) the normal stresses in the bronze and steel rods (01,02). (b) the downward deflection v of rigid bar ABC.
q2: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm-diameter steel E = 200 GPa rods, as shown inthe figure. Use a = 2.705 m, b = 1.821 m, and L= 4 M.For a load of P = 117 kN, determine thedisplacement of joint F. Unit should be in mm
The steel propeller shaft ABCD carries the axial loads shown inFig. (a). Determine the change in the length of the shaft causedby these loads. Use E = 29×106 psi for steel.
Refer to the figure below and using the following:F1= 8 kNF2 = 10 kNa = 2 mb = 2 mWhat gives the axial force for members DE, BC, EF, GCWhat gives the reaction at the pin support?
A small balcony constructed of wood is supported by three identical cantilever beams (see figure). Each beam has length L, = 2.3 m, width b, and height h = 3b/2. The dimensions of the balcony floor are L, x L2, with La = 2.7 m. The design load is 6.5 kPa acting over the entire floor area. (This load accounts for all loads except the weights of the cantilever beams, which have a weight density y = 6.5 kN/m^3 --) The allowable bending stress in the cantilevers is 45 MPa (a) Assuming that the middle cantilever supports 50% of the load and each outer cantilever supports 25% of the load, determine the required dimension b. Round to the nearest whole number. mm (b) Assuming that the middle cantilever supports 50% of the load and each outer cantilever supports 25% of the load, determine the required dimension h. Round to the nearest whole number. h = mm