Member ABC, which is supported by a pin and bracket at C and a cable BD, was designed to support the 50-kN load Pas shown. Knowing that the ultimate load for cable BD is 150 kN, determine the factor of safety with respect to cable failure. 40 30° B 60 cm P 80 cm 40 cm

Member ABC, which is supported by a pin and bracket at C and a cable BD, was designed to support the 50-kN load Pas shown. Knowing that the ultimate load for cable BD is 150 kN, determine the factor of safety with respect to cable failure. 40 30° B 60 cm P 80 cm 40 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 607 mm 605 mm C A B 25.5mm 53 mm f the gap between C and the rigid wall at D is initially 0.153 mm,…

A: Given. The load (P)= 205KN GAP BETWEEN CD =0.153 mm Our aim is to calculate the support Reactions.…

Q: The channel consists of a smooth cement section (m = 0.109) and overflow regions on each side that…

A: Given: The value of m in the cement section is 0.109. The value of m in a light brush is 1.54. The…

Q: the slope-deflection method, draw the bending moment diagram. 3m B 2EJ 4m 20kN/m 3m 5. Moment @D…

Q: . The welded connection shown in the figure uses electrodes E70XX. The nominal weld strength of the…

Q: 16 cm 8 cm 8 cm 8 cm -X

Q: 3 (a) Briefly give the theory of distribution and transporation of suspended material and derive the…

Q: Q/Deduce the ISO from the projections 60 80 30 40 R30

Q: trough is filled with a liquid of density 8232 N/m^3. The ends of the trough are equilateral…

Q: Problem 1. Determine the axial forces, shears, and bending moments at points A and B of the…

Q: An equal tangent vertical curve is intended to connect grades of 4.2% and -3%. If this curve is to…

A: n1= 4.2%n2= -3%V = 60mph = 96.56 kmph It has been asked in the question to determine the minimum…

Q: What is the importance of understanding the quantitative analysis of hydrology?

A: Hydrology and its applications in engineering are unavoidable when planning and constructing…

Q: Problem Number 6. A simply supported beam has a length of 4m. The beam is carrying a 500N downward…

A: L = 4m

Q: A city disposes of its treated wastes to a river on a continuous basis. The minimum flow in river is…

A: The given data is: The stream and river discharge, Q=210 m3/s Pollution limit, Ps=0.4 mg/l Waste…

Q: The steel truss was subjected to horizontal force 2kN at C. Find the m of AC using the method of…

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-section of the beam…

Q: Looking at the x direction, provide the front view, top view, and left-side view

Q: the elevation at the highes

A: PVCsta=PVIsta-L2PVCsta=(18420)-L2PVCelv=PVIelv-g1L2PVCelv=80.522-0.04×L2PVCelv=80.522-0.02×Lso,Equat…

Q: For deflection y units in a beam which of the following relation holds good? OⓇ = dy/dx de/dx =…

A: deflection in beam is equal to y Questions is from structural analysis here the defection in beam is…

Q: the answer as soon as

A: Given data- Discharge (Q) = 15000m³/day = 15000m³/24hr = 625m³/hr Detention…

Q: A ductile material is subjected to a tensile test. The yield strength was determined to be 100 MPa.…

Q: A 120m by 120m lot is to be divided into 9 equal square sections. The elevations of the ground…

Q: For the beam subjected to the loadings as shown, determine the following: 52 kN 40 kN/m 2m 4m B 2m C…

A: a. draw the shear and moment diagrams specifying values at all change of loading positions and at…

Q: Determine the depth in m of the trapezoidal channel with sides inclined 45 deg with the horizontal…

Q: Solve the following. Force P acting at an angle of 45° from the x-axis, along xy plane, prevents the…

Q: B | 0.75 m 2.07m The rigid bar AB of negligible weight is supported by a pin at 0. When the two…

Q: 1. Calculate the acceleration of block A in ft/sec2 2. Calculate the acceleration of block C in…

Q: STATICALLY INDETERMINATE BEAMS Using Double Integration Method and/or Moment Area Method, answer -2…

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-section of the beam…

Q: 23. Referring to problem 22, the value computed from the governing interaction equation or formula…

A: Pa = 1188KN

Q: venturi meter of 150 × 75 mm size is fixed in a horizontal pipe carrying water. The pressure gauge…

Q: Problem 5. (HKS Problem 7.16) For the cases in the figure below, determine the pressure, elevation…

Q: Problem 2.4 On the basis of isopluvial maps, the 50 years 24 hr maximum rainfall at Bangalore is…

Q: A perfect gas has a value of R= 0.317 ks/ka-k and k>1.27 - If noks are added to 2.75 KG of this…

Q: 0 60 ។ rectangular components. 70KN 3 45° 4x 100 KN B) 30 50KN

Q: the contour lines at the site of a reservoir are as follows. 144 142 Contours (m) 158 156 154 152…

Q: B D 8 ft 6 ft 8 ft 8 ft 6 ft 33 kips The cross-sectional area of each member of the truss is 1.75…

Q: Determine the deflection at the free end of the given overhanging beam. Use the Three Moment…

A: Given:

Q: The uniform sign has a weight of 7.5 kN and is supported by the pipe AB, which has an inner radius…

Q: Q.2] Find the reactions at point A for the structure shown in the figure. zkN/m A M 10m 5m 20 KN #

A: Draw the FBD of the beam showing all forces and reactions. Then using equilibrium equations the…

Q: Petroleum was made to flow through 2.0km in a pipe with diameter of 0.28m. The rate of flow is 36…

Q: SOON - 2m 450 N 10m 1.01 (d)

Q: the critical DO

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is the thickness of a slab foundation that is 16 feet by 50 feet for first floor and second…

A: L = 50 ft B = 16 ft

Q: Problem 5. (HKS Problem 7.16) For the cases in the figure below, determine the pressure, elevation…

Q: Problem 1. Determine the axial forces, shears, and bending moments at points A and B of the…

Q: Double Integration

Q: The three-hinged tied arch is subjected to the loading shown. Determine the force in members CH and…

Q: totsa 1m [102 Find The deflection at Doint AFH 6 Oc день TOEN A € B Im EI 25 как E 2EI F 4m

Q: A steel beam is simply supported on a span of 12 meters. Given: Section: W410mm x 100 kg/m Area, A=…

A: Answer To determine the live load P in KN we need to calculate the design flexural strength of the…

Q: 3- For the beam given in the figure, a- Draw the elastic curve by using the Mohr Method. b-…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Member ABC, which is supported by a pin
and bracket at C and a cable BD, was
designed to support the 50-kN load Pas
shown. Knowing that the ultimate load for
cable BD is 150 kN, determine the factor of
safety with respect to cable failure.
40
30°
B
60 cm
P
80 cm
40 cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The left support of the cable shown islocated 10 m below the right support.The lowest point on the cable is 13 mbelow the right support. If the maximumtension in the cable resulting from auniformly distributed load w along thehorizontal is 400 kN, determine:a. The angle between the cableand the horizontal at the rightsupport;b. The magnitude of the distributedload wc. The length of the cable.
A cable is supported at points A and B which are 250m horizontally apart and with point B 20m below point A. The cable is loaded by 4 kN/m along the horizontal and its slope at point B is equal to zero. Find the tension at the points of supports. ANS.TA = 6329.5 kNTB = 6250 kN
The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 620 N, determine the n- and t-components of this force acting on point A of the bar.
Determine the Tension in Cable "Ta" if Td=300kn.
The man attempts to pull down the tree using thecable and small pulley arrangement shown. If the tension inAB is 60 lb, determine the tension in cable CAD and theangle θ which the cable makes at the pulley.
Determine the tension in cable BD if P = 51 N.
The cable AB keeps the 8-kg collar A in place on the smooth bar CD. The y axis points upward. What is the tension in the cable?
The load on the cable AB is uniformly varying. It is attached to a wall at A and is balanced at B by a horizontal force of 1340 N. Calculate the load intensity (W) at point A. DRAW COMPLETE FBD
The power transmission cable weighs 150 N>m. Ifthe resultant horizontal force on tower BD is required to bezero, determine the sag h of cable BC.
A rigid bar ABCD is pinned at endA and supported by two cables atpoints B and C (see figure). Thecable at B has nominal diameterdB =25 mm and the cable at C hasnominal diameter dC = 30 mm. Aload P acts at end D of the bar.What is the allowable load P if thetemperature rises by 90°C andeach cable is required to have afactor of safety of at least 5against its ultimate load?(Note: The cables have effective modulus of elasticity E = 150GPa and coefficient of thermal expansion  = 12 x 10–6/°C. Other properties of thecables can be found in Table 2-1)
The cable is carrying a horizontal uniform load of 7.5 KN/m, and point C is the lowest point in the cable. Find: 1. The Maximum Tension (Tmax) on the cable. 2. The Cable Diameter if the allowable tensile force is 1.450 Mpa 3. The length of the cables considering the given sag.
Determine the total length of cable, If y=20m. a.) 177.809 KN b.) 176.089 KN c.) 175.980 KN d.) None of the above e.) 178.908 KN