message or information signal will be encoded onto the carrier signal. i) Sketch a DSB-SC signal in the time-domain, identifying any key features. Include the message signal in your plot. Describe the key differences between your sketch and that of a DSB- AM signal. ii) Calculate the operating bandwidth of the DSB-SC signal assuming the message signal is audio (40 Hz to 4 kHz). Would this be any different if DSB-AM were used instead? Explain your answer.

message or information signal will be encoded onto the carrier signal. i) Sketch a DSB-SC signal in the time-domain, identifying any key features. Include the message signal in your plot. Describe the key differences between your sketch and that of a DSB- AM signal. ii) Calculate the operating bandwidth of the DSB-SC signal assuming the message signal is audio (40 Hz to 4 kHz). Would this be any different if DSB-AM were used instead? Explain your answer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. AM modulation is inefficient. With reference to the frequency domain, explain why. How does double sideband and single sideband suppressed carrier modulation improve the efficiency of AM modulation? Despite its increased efficiency, what is a disadvantage of SSB-SC when compared with AM modulation.b. An antenna has an impedance of 75 Ω. An unmodulated AM signal produces a current of 3.4A. The modulation is 90 percent. Calculate (a) the carrier power, (b) the total power, and (c) the sideband power.c. With aid of diagrams, explain how frequency modulation works. d. A 450-MHz radio transmitter uses FM with a maximum allowed deviation of 6 kHz and a maximum modulating frequency of 3.5 kHz. What is the minimum bandwidth required? Use Figure. 5.1 to determine the approximate amplitudes of the carrier and the first three significant sidebands
In Amplitude modulation, Vestigal Side Band (VSB) is one of the technique used to overcome its limitations in terms of power and bandwidth. With this in mind; a. Explain how a VSB signal is generated in the transmitter. b. Draw and compare the frequency spectrum of the original message signal and the spectrum of the VSB signal in a frequency domain. c. Show how the bandwidth of VSB is calculated by writing the equation. d. Give one application of VSB in broadcasting.
For single sideband (SSB) modulation d) Explain with drawing the demodulation process of SSB signal.e) How many single sideband (SSB) stations can be accommodated in a 180 KHz bandwidth if the highest modulating signal frequency fmax is 9 KHz?f) What are the main advantages and disadvantages of single sideband (SSB) modulation compared with ordinary amplitude modulation (AM).
In AM modulation, the equation of the modulating signal is given by f(t) = Am cos ωm t. If the amplitude of the carrier wave is A and there is no over–modulation, then what will be the modulation efficiency?
Explain why we can still receive monophonic FM signal with our stereophonic FM receiver by showing its block diagram and discussing it
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 750 kHz is amplitude-modulated by a 4 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 180Vp and 70Vp respectively. The equivalent resistance of the transmitting antenna is 60 Ω. Determine: (i) The peak amplitudes of the audio, carrier sideband voltages and modulation index. (ii) Using the above results, write the complete AM mathematical representation to express the waveform, showing its carrier, lower sideband and upper sideband parameters. (iii) The power of the carrier signal, total sidebands power and the bandwidth of the modulated signal. Then sketch and label the power spectrum of the modulated ( i v ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC
A digital communication link carries binary-coded words representing samples of an input signal, xa(t)=3cos⁡(600πt)+2cos⁡(1800πt)The link is operated at 1,000 samples/s. (a) What is the folding frequency? (b) What is the Nyquist rate for the signal xa(t)? (c) What are the frequencies in the resulting discrete-time signal x(n)? (d) Will there be any aliasing here? (e) Which frequency will alias to what frequency
From the given electrical system get the transfer function ??(?)/?(?). Write the answer in a single fraction and make sure to arrange the degree of variables in descending order.
1. We use the DFT to compute the amplitude spectrum of a sampled data sequence with a sampling rate fs =2,000Hz. It requires the frequency resolution to be less than 0.5 Hz. determine the number of data points used by the FFT algorithm and actual frequency resolution in Hz, assuming that the data samples are available for selecting the number of data points.
1. What type of transmissions represented the first type of digital communications?A. Digital signal processing B. Amplitude-shift keying C. Morse codeD. On-off keying 2. Each form of digital modulation has implications in terms of spectral efficiency, power distribution, and _________.A. amplitudeB. bandwidth C. performanceD. distortion3. Which of the following is a key characteristic of orthogonal frequency-division multiplexing?A. Amplitude modulationB. Noise performanceC. Digital modulationD. Spectral efficiency4. When a carrier is conveying intelligence by simply turning it on or off according to a prearranged code, this type of transmission is called ____________.A. continuous waveB. sine waveC. square waveD. cosine wave5. Why must modulated signals be demodulated?A. To recover the original intelligenceB. To improve the spectral efficiency of digital transmissionsC. To enable implementation of advanced featuresD. To produce one or more significant sideband pairs 6. What is one…
A 1500 KHz carrier with amplitude of 50 V is amplitude modulated by 2 –KHz sine wave tone with a peak voltage of 15 V. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
Two of the major design characteristics for ADCs are 1) bit depth or resolution and 2) sampling rate. Briefly explain these concepts and how they impact analytical data. Before all music was available online, but after LPs and 8track, CDs were the common format for recorded music. Give a rationale for the industry standard of recording pieces at 44.1 kHz. What are the benefits and the limitations of this choice? Briefly describe the differences between Fourier Transforms and Discrete Fourier Transforms.