mm 74.5 mm C 184 mm 147.5 mm 2.4 kN +10m A T-beam is constructed from two 2 X 8 (two-by-eight) pieces of lumber, nailed together as shown. Each piece has actual dimensions of 38 mm x 184 mm. The beam cross section has a moment of inertia about its centroidal x-axis of I = 63.64 x10^6 mm4. The Distance between supports A and B is 4 m. Determine: 1) Shear stress at a distance of 2m to the right of A, and 10 mm above the bottom edge of the beam. Enter this value into D2L box, in MPa. (4 decimal places) 2) State specifically where the maximum shear stress is along the beam. No need to calculate the max shear stress.

mm 74.5 mm C 184 mm 147.5 mm 2.4 kN +10m A T-beam is constructed from two 2 X 8 (two-by-eight) pieces of lumber, nailed together as shown. Each piece has actual dimensions of 38 mm x 184 mm. The beam cross section has a moment of inertia about its centroidal x-axis of I = 63.64 x10^6 mm4. The Distance between supports A and B is 4 m. Determine: 1) Shear stress at a distance of 2m to the right of A, and 10 mm above the bottom edge of the beam. Enter this value into D2L box, in MPa. (4 decimal places) 2) State specifically where the maximum shear stress is along the beam. No need to calculate the max shear stress.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
Given both questions are subparts please give me both solutions. Which of the following gives the bending moment at point A on the beam shown (KN-m)? A. zero B. 895 C.1000 D.375 Which of the following gives the axial and shear force at point A on the beam, respectively(KN)? A. 45 and 66.667 B.75 and 91.667 C. 60 and 121.667 D. 75 and 283.333
A prismatic continuous beam is shown. The flexural rigidity is 100 000 N. m². The problem maybe solve using superposition method. 1. Determine the vertical midspan deflection due to the given loads in millimeters if the middle support is removed. a. 5.83 b. 6.20 c. 4.95 d. 7.17 2. Determine the vertical midspan deflection due to an upward unit load at midpoint in millimeters if the middle support is removed. a. 0.513 b. 0.678 c. 0.245 d. 0.360 3. Determine the reaction at the middle support in Newton’s. a. 29.5 b. 13.8 c. 36.2 d. 47.0
Five forces are applied to the beam trolley as shown. Determine the y-coordinate of the point on the y-axis through which the stand-alone resultant R must pass if F = 4.5 kN and θ = 20°. Point O is at the center of the I-beam.
The section of an I beam is made out of two identical flanges and a web. The width of Flange is 260mm and thickness 25mm. Web thickness is 10mm and the total depth of the section is 715 mm. fy=300mPa, ZX=5760X103 mm3 and SX=6390X103mm3. Determine the moment section capacity of the section
Design a most economical spiral-column cross-section to support factored forces and end moments of Pu = 1,600 kips and Mu = 150 kip-ft. Assume that the centroid of each longitudinal bar from the edge of the column is 2.5 inch. What is the trial diameter dimension of the section in inch if ρg = 0.025?
A W section is used as a beam without lateral support. A36 steel is used with Fy3D248 MPa. Compute the allowable bending stress(MPa) if it has a simple span of 9 m. Properties of W Section A=24709.6 mm2 d 840.74 mm tw3D14.73 mm I 2792.9 x 106 mm I, 90.74 x 106 mm S= 6653.15 x 103 mm b= 292.35 mm ty%3D21.72mm We Ar Sy 621.07 x 103 mm %3D De ry=335.28 mm Fla Ty = 60.45 mm Flar Wel Mor Sect Ime tw mm d. by
Determine the slope at points B and C of the beam given. If E=200 GPa and I=360×10⁶mm⁴.
The simple beam 120mm x 420 mm cross section has E= 9.50 GPA Determine the vertical movement of point B
Draw the shear and moment of the beam shown by Shear and Moment Equation Method and by Relation of Load to Shear and Moment Method. P=74 6P= 6(74) = 444 kN 8P = 8(74) = 692 kN
W= 465kN/mUsing Slope Deflection Method, determine all reactions at supports also, determine shear andbending moments with complete labels. Use |=1/12 bh^3 and E = 2.15x10^7 KPa
9.64 If h = 350 mm , locate the centroid y of the cross-sectional area of the built-up beam.