MT.Q2- Calculate the voltages Vo and V, the currents lo and ly, the power of A in the circuit via Ohm'sLaw, KVL, and KCL. The voltage sources of the circuit are Vs - 96 Volt, Vs- 24 Volt.1302501024470Vab70TÜM HESAPLAMALARDA VE BULUNAN DEĞERLERİN DENKLEMLERDEKULLANIMINDA VİRGÜLDEN SONRA 3 BASAMAK ALARAK İSLEMYAPILACAKTIR. CEVAP ANAHTARLARI BUNA GÖRE OLIISTURULDU.Vo-Va-l%3DIx=

We need to tell about the voltage and current value , we will find out it by using kvl ,kcl and…

MT.Q2- Calculate the voltages Vo and Va, the currents lo and Iy, the power of A in the circuit via Ohm's Law, KVL, and KCL. The voltage sources of the circuit are Vs-96 Volt, Ve- 24 Volt. 130 252 102 Www 70 70

MT.Q2- Calculate the voltages Vo and Va, the currents lo and Iy, the power of A in the circuit via Ohm's Law, KVL, and KCL. The voltage sources of the circuit are Vs-96 Volt, Ve- 24 Volt. 130 252 102 Www 70 70

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A set of copper conductors on a branch circuit serve a water pump motor rated at 20A. The pump is 100ft from a 220V power source. Compute the line losses of No. 14 AWG copper conductor. (Hint: The conductor has a resistance of 2.57 ohms/1000ft) a. None of these b. 40.8W c.64.8 W d.102.8W e. 205.6W
The sizes of the given circuit elements are given below.What is the average power delivered by the Is current source?R1 = 8 ohmsR2 = 8 ohmsL1 = 9 milliHenryL2 = 8 milliHenryn = 3V0 = 50cos(1300t+30) Volts
Two resistors Ra and Rb, are connected in parallel, Ra having a value of 33.40909 ohms and Rb being adjustable over a wide range. The parallel combination is then connected through a 105 ohm line resistor to a 211-volt source. If Rb is adjusted so that the power of Ra will be maximum, how many watts will Ra takes under this condition?
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5 + j4) ohms, Z2 = 10 bar angle of -30° ohms, and Z3 = 15e j0.758 ohms, calculate the currrent flowing in each resistor. Use Nodal analysis.
A certain installation has 150 kW, 400V, 0.9 pf, 3 phase load. Load is to be fed by a 4core cable. Length of the cable will be 150 m. If the cable surrounding temperature is350C, cable runs in a separate path (without any other cables) and allowable total voltagedrop is 5% of nominal voltage, what is the allowable maximum voltage drop of thecable?i. 0.378 mV/A/mii. 0.347 mV/A/miii. 0.424 mV/A/miv. 0.512 mV/A/m v. 0.554 mV/A/m
Norton’s Theorem1. Connect the circuit shown in the figure 2. Measure and record the current I passing through in the 50 ohm resistor.3. Remove the 50 ohm resistor from terminals c and d.4. Connect the ammeter to measure and record IN 5. Remove the power supply from nodes a and b and place a short-circuit conductor to replace the power supply between nodes a and b. 6. Using the digital multimeter, measure RN.7. Using the measured IN and RN, compute for the current passing through the 50 ohm resistor.10. For the computed values, compute for IN, RN and the current passing though the 50 ohm resistor, I’.
In a house there is a three-wire system configured as follows. A refrigerator with an impedance of (10 + j 10) Ω is connected to line L1 and to neutral, and to line L2 and neutral all the lighting in the house consists of 10 luminaires of 20 W each. In addition, there is a 240 V dryer that consumes 8 kW. Calculate a) current of line L1 and line L2 and neutral b) total power consumed.
PLEASE ZHOW COMPLETE SOLUTION. NEED super ASAP. TIA!
Good day, sir/ma'am. Question: A battery has an emf of 14 V and internal resistance of 0.08 ohms. Its terminals are connected to a load resistance of 3.00 ohms. a.) Find the terminal voltage of the battery. b.) Calculate the power delivered to the load resistor and the power to the internal resistance of the battery. Thank you.
Calculate ( C ) Load current, Calculate ( D ) Power in the load resistor or Power in the 50 ohms resistor, Calculate ( B ) Rth, Calculate ( A) Vth
The percent values of the voltage, current, impedance, and volt-amperes for a givenpower system are 90, 30, 80, and 150 percent, respectively. The base current and baseimpedance are 60A and 40Ω, respectively. Calculate the actual values of the voltage,current, impedance, and volt-amperes.
note: use article 220 NEC , APPLY STANDARD METHOD 1. A house has a floor area of 1000 ft2, The appliances are an 11 kW stove and a 10 kV, 240 V dryer. Assume that the kW rating of the stove and dryer are equivalent to the kVA rating. - Calculate general lighting load. - Estimate the number of lighting circuits that will be 20A at 120V. - Estimate the number of circuits there will be at 20A at 120V for small appliances and laundry. - Calculate the TOTAL EFFECTIVE LOAD (VA). - Estimate the main circuit breaker and THHW conductors at 75 celsius and neutral for 120/240 volts. Translated with DeepL.com (free version)