n()= 100 sin(10) at t< o m(0)- 200 sin(10) at t0 A coil has been connected to an AC source for a long time and at t-0 the voltage source has changed from v(t= 100 sin(10/) to v.(t)= 200 sin(10/). If the reactance and resistance of the coil is 40 and 30 respectively, then, the circuit current i(t) is

n()= 100 sin(10) at t< o m(0)- 200 sin(10) at t0 A coil has been connected to an AC source for a long time and at t-0 the voltage source has changed from v(t= 100 sin(10/) to v.(t)= 200 sin(10/). If the reactance and resistance of the coil is 40 and 30 respectively, then, the circuit current i(t) is

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Similar questions

A conducting coil, with current i(t) = 4.40e−0.0250t sin(120πt), with i in amperes and t in seconds, is placed next to a second coil, end to end. At t = 0.720 s, a lab tech measures the emf across the second coil, and the result is −3.50 V. What is the mutual inductance (in mH) of the coils?
The voltage pulse applied to the 100 mH inductor shown is 0 for t<0. and is given by the expression v(t)=20te−10t V for t>0. Also assume i=0 for t≤0. Sketch the voltage as a function of time.
The starting voltage of the C = 0.05 microfarad capacitor given in the figure is V0 = 30 Volts and the starting current of the coil is I0 = 0 amperes. in this case the voltage response of the circuit; For t> = 0, since V (t) = - 10 e-5000 + 40e-20000 volts, iL (t) current iL (t) current t = 0.0003 mA per second.
The voltage pulse applied to the 100 mH inductor shown is 0 for t<0 and is given by the expression v(t)=20te−10t V for t>0. Also assume i=0 for t≤0. Sketch the current as a function of time.
All capacitors were initially discharged. at t = 0, S1 is placed at position 1 and S2 is closed. During this phase, it has been determined that Eth and Rth seen by the equivalent capacitor are, respectively, 20 V and 6.0 kΩ. The time constant is 29 ms. At t = 15 ms, S1 is placed at position 2 and S2 is kept closed. Calculate the equivalent capacitor voltage vT at t = 15 ms. Enter your answer in V rounded to 2 decimal places. At t = 25 ms, S1 is kept at position 2 and S2 is opened. Data: R1 = 5 kΩ, R2 = 3 kΩ, R4 = 2 kΩ, R5 = 20 kΩ, R6 = 12.0 kΩ;
A circuit is constructed with an AC generator, a resistor, capacitor and inductor as shown. The generator voltage varies in time as ε =Va - Vb = εmsinωt, where εm = 120 V and ω = 726 radians/second. The values for the remaining circuit components are: R = 62 Ω, L = 95.6 mH, and C = 13.8μF. 4) What is t1, the first time after t = 0 when the voltage across the inductor is zero? 6) What is VC = Vd - Va, the voltage across the capacitor, at time t = 0? Note that VC is a signed number.
An electrical circuit has a very small resistance so it can be despised. The capacitor on the left was charged up to the voltage of Vo=10 volts and then, at time t=0, the switch S was closed. The capacity of the capacitors are C=60 µF, and the coil inductance is L=0.04 HI) Find the voltage on the left capacitor, at the instant V1=0.001 s.II) Find the voltage in the right capacitor, at the instant t=002 s.
The capacitor of external defibrillator must be loaded at 1500V, in order to generate a two-phase wave of 150 J.Considering a transthoracic impedance is 80ohms and a capacitance of 30 000 uF. 3- What is the energy of the capacitor?4- What is the internal impedance of the defibrillator in the previous cases?
An industrial coil is modeled as a series combination of an inductance L and resistance R, as shown in the figure below. Since an ac voltmeter measures only the magnitude of a sinusoid, the following measurements are taken at 60 Hz when the circuit operates in the steady state: Using the instruction provided, find L (in millihenries) when E = 166 V, V1 = 80 V, VO = 101 V. Round off to 5 decimal places if applicable.
12. 7.12 In the circuit , let Ig represent the dc current source, σrepresent the fraction of initial energy stored in the inductor that isdissipated in to seconds, and L represent the inductance. 1. a) Show thatR=Lln[1/(1−σ)]2to
The current source in the circuit shown generates the current pulse i g ( t ) = 0, t<0, i g ( t ) = 8 e −300t −8 e −1200t A, t≥0. Find (a) v(0); (b) the instant of time, greater than zero, when the voltage v passes through zero; (c) the expression for the power delivered to the inductor; (d) the instant when the power delivered to the inductor is maximum; (e) the maximum power; (f) the instant of time when the stored energy is maximum; and (g) the maximum energy stored in the inductor.
An industrial coil is modeled as a series combination of an inductance L and resistance R, as shown in the figure below. Since an ac voltmeter measures only the magnitude of a sinusoid, the following measurements are taken at 60 Hz when the circuit operates in the steady state: Using the instruction provided, find R when E = 166 V, V1 = 80 V, VO = 101 V. Round off to 5 decimal places if applicable.