n orifice on the side of a tank discharges water under a head of 9 ft. if the diameter of the orifice is 2”, the coefficient of contraction is 0.63, and the head lost is 0.80 ft, determine the discharge, CV and CD. Pls show also the figure/diagram

n orifice on the side of a tank discharges water under a head of 9 ft. if the diameter of the orifice is 2”, the coefficient of contraction is 0.63, and the head lost is 0.80 ft, determine the discharge, CV and CD. Pls show also the figure/diagram

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Related questions

Q: Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the a...

A: To find the absolute value of maximum shear produced

Q: A foundation carries uniform loads as shown. Determine the value of w (in kN/m). 円円 W (kN/m) 4m

A: To find :- w developed at the footing base.

Q: The 5-day BOD of a wastewater sample is obtained as 190 mg/l (with k = 0.01 h). The ultimate oxygen ...

Q: Figure Q4 shows a two-hinged arch of parabolic shape supported by pinned at both A and C. The arch i...

Q: the relationship between Oxy and the different strain components from indicial notation:

A: relationship between σyz and different strain cpmponent from σkL = Cklmn εmn where σyz =stres...

Q: The data from a closed traverse ABCD are given in the table below: Line Included angle (in degrees) ...

A: Given data,

Q: RIN/m A shallow foundation shown below, with e,=0.34 m and eg=0.28 m. Water level is located at a de...

Q: A circular culvert 164 ft long extends between two reservoirs as shown. The difference in water surf...

A: Given Data - Length of circular culvert - 164 ft Difference between water surface elevation between ...

Q: ment (positive if counterclolewise, negative if clockwise) of the 290-N force of the bolt. 290 N 26 ...

A: Horizontal Component = 290 x sin 26 = 127.27N Vertical Component = 290 x Cos26 = 260.65 N

Q: Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.

Q: 1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shear...

Q: Instructions: Draw the three basic orthographic projections of the figure. (Top View, Front View, Ri...

A: Hand made drawing are attached herewith of different views. Which will give you idea about different...

Q: Determine the magnitude F and direction 8 (measured clockwise from the positive y-axis which is down...

A: Equating the components of forces acting along x and y directions:Along x-axis:12.9 cos26°+7.4 cos26...

Q: 70 kN/m 70kNm 円円 W (kN/m) 4m 2m tuzt wat twet wet w

A: Given, => Downward Uniformly distributed loads 1. 70kn/m at 3m from left end 2. 70kn/m a...

Q: cantilever beam is loaded as shown in the figt ssume that El = 74x103 kN-m² for the beam. 40 kN/m

A: VA = All Forces Acting In ydirection Hence Its is = - ( 40 x 2) = 80Kn MA = Taking moment abo...

Q: A light-weight concrete was cast-in-place to form a rectangular beam. If its unit weight is 17.24 kN...

Q: From the frame shown, solve for the moment reaction at fixed support. (kN m) a. 490 CCW b. 530 C...

A: Given data in question UDL Span member length Point load To find out Resisting moment at point A

Q: Determine the location of Neutral Axis, in mm, from the top of the section.

Q: A circular culvert 164 ft long extends between two reservoirs as shown. The difference in water surf...

A: Given -

Q: beam AB supporting two concentrated loads P has a rectangular cross section of width b = 100 mm and ...

A: The answer is found to be P=8.250 KN For explanation please refer to the attached solution, thanks

Q: Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the a...

A: cantilever beam : A cantilever is a horizontally extending rigid structural element with just one en...

Q: A continuous beam is subjected to a dead load of 10 kN/m and a live load of 25 kN/m. Use NSCP 2001 p...

Q: What is the mass (lbm) of an object that has a base area of 4 inch2 which exerts a pressure of 25 ps...

Q: Determine Y-bar and the Moment of Inertia about the Neurtal Axis, IN/A, and the corresponding Radius...

Q: 1 Draw shear and moment diagram. Det. max. V and max. M 2. Draw loading and moment diagram given the...

Q: Determine the dimensions of a T-shaped retaining wall for a height of 4 m above the ground level. Th...

Q: Draw the shear and moment diagram. Use Moment Distribution Method (MDM)

Q: 250 300 250 100 200 175 A 75 600

Q: An open cylindrical tank 30 cm in diameter and 80 cm high is partially filled with water. It is rota...

Q: This is a helpful way of thinking and design that takes into consideration the use of materials that...

A: Answer:- Sustainable Design Sustainable building design and it's construction is the best practice o...

Q: Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-...

Q: Write the shear and moment equations (not simplified and simplified) at each segment of the beam sho...

Q: A gusset plate is connected to the flange of column with the help of fillet weld on both sides as sh...

Q: An angle section ISA 120 x 100 x 10 is shown in the figure. The bolts used are of diameter 20 mm. Fi...

A: Given data, For ISA 120x100x10 Diameter=20 mm Steel grade is Fe410

Q: A retaining vertical wall 5 m high is retaining a sand of unit weight 17 kN/m3 for which o = 35°, th...

Q: The floor frame shown carries a (superimposed) service dead load of 2.2 kPa. Slab S1 is 110 mm thick...

A: We have to determine the value of dead load carried by the different beams and girders also compute ...

Q: A wooden beam AB supporting two concentrated loads P has a rectangular cross section of width b = 10...

A: Draw the FBD of the given beam and draw the bending moment diagram. From the diagram locate the segm...

Q: A rectangular cantilever beam of span 4 m is 35 cm x 65 cm in cross-section. Bending moment at the s...

Q: Find the hydraulic radius of the 4m deep canal.

A: Given data - Top width(T) = 12m Bottom width(B) = 6m Height(H) = 4m

Q: D В Bm 4m 3m A E G H 3m 3m 3m 3m 30KN 60KN 90KN

Q: What is the pH of the solution containing 10-5 M H2SO4? Assume complete dissociation of H2SO4 in wat...

A: To find the pH of the solution

Q: discussfineness modulus

Q: A gravity dam of trapezoidal cross section with one face vertical and horizontal base is 22m high an...

Q: Using Meyerhof's General Bearing Capacity Equation, calculate the Net Allowable Bearing Capacity of ...

Q: 3 m 1.5 m Draw The Moment diagram for the beam

A: Given -

Q: For the beam shown, do the following: 1. Determine the values of shear at every change of load point...

A: As per company's guidelines we can only answer first three questions. Kindly post other questions as...

Q: Situation 2: A square tied column carries an axial dead load of 500 kN and an axial live load of 800...

A: Situation 2 Given data, Deal load D = 500 kN Live load L = 800 kN fc' = 28 MPa, fy = 275 MPa Bar dia...

Q: For the beam loaded as shown in the figure below, determine the following unknowns using any geometr...

Q: Determine which of the truss systems shown in a) to e) are statically determinate, statically indete...

A: Given - Five structures a, b, c , d , e are given in the problem. It is asked to determine whethe...

Q: Design the Slabs of the shown Structure.

A: To design the slab for the given specifications

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

An orifice on the side of a tank discharges water under a head of 9 ft. if the diameter of the orifice is 2”, the coefficient of contraction is 0.63, and the head lost is 0.80 ft, determine the discharge, CV and CD. Pls show also the figure/diagram

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

7. As shown in the figure below, a pump lifts water through a 100-mm diameter ductile iron pipe (friction factor f = 0.0251) from a lower to an upper reservoir. If the difference in elevation between the reservoir surfaces is 10m, and the pump performance curve is given by H = 15 - 0.1Q2, where H is in m and Q in L/s. (1) Determine the system head curve (relationship between TDH and Q) assuming the entrance and exit loss coefficients are both 1; (2) Estimate the flow rate through the system; (3) If the minimum NPSH for this case is 1.5m, determine the maximum height above the lower reservoir that the pump can be placed (assuming that the atmospheric pressure Pa=101 kPa, specific weight of water γ = 9.79 kN/m3, and the water vapor pressure Pv = 2.34 kPa).
1. A rectangular channel has a contraction that smoothly changes the width to a minimum width of 1.5 f t (the throat). If the flow is critical at the throat, find the volume flow rate when the depth at the throat is 1.5 f t. 2. Water in an open channel of constant width flows over a bump of height 1 f t, as shown in Figure P10.10. What is the depth of the water Y2? Assume uniform flow of constant width with no losses.
As shown in the figure below, a pump lifts water through a 100-mm diameterductile iron pipe (friction factor f = 0.0251) from a lower to an upper reservoir. If the differencein elevation between the reservoir surfaces is 10 m, and the pump performance curve is givenby H = 15 – 0.1Q2, where H is in m and Q in L/s.a. Determine the system head curve (relationship between TDH and Q) assuming theentrance and exit loss coefficients are both 1b. Estimate the flow rate through the systemc. If the minimum NPSH for this case is 1.5 m, determine the maximum height above thelower reservoir that the pump can be placed (assuming that the atmospheric pressure Pa=101 kPa, specific weight of water ? = 9.79 kN/m3, and the water vapor pressure Pv= 2.34 kPa).
Flow occurs over a spillway, as shown in the figure. Determine the horizontal force on thespillway per unit width.
A 3 ft diameter log with specific gravity of 0.82 divides two shallow ponds as shown in the figure. If log is 12 ft long. Use unit weight of water = 62.4 lb/ft³. Compute the following. A. Horizontal and vertical reaction at point C (include direction) B. Resultant reaction force (include direction) C. Angle of resultant reaction force
Water flows through the pipe contraction as shown in the figure. The drop in the piezometer level after contraction is 0.1 ft. Determine the flow rate as a function of the small pipe diameter, D. What is the flow rate if D = 6 in.
A sharp-edged orifice having a diameter of 0.0285 m is installed in a 0.25-m pipe through which a liquid having a density of 1050 kg/m3 and a viscosity of 1.5 cp is flowing. The measured pressure difference across the orifice is 120 kN/m2. Calculate the volumetric flow rate in li/s. Assume that Co = 0.61.
A conical tank is inclined with an angle of 60°. A hole with radius 2-in was opened at the bottom. If initially the tank is full to a height of 9 ft, how long will the tank drain? Consider a coefficient of contraction, 0.6.
Situation 1 Q. If the flow rate of water through the pipe system shown in the following figure is 0.050 m^3/s under total head loss of 9.0 m, assuming a C coefficient of 120 for all pipes determine the following, 1. The head loss in pipe B. 2. The flow in pipe B, in m3/s. 3. The diameter of pipe C.
Water at 20°C is flowing through through a narrow section as is seen in the figure. There is a 20 kPa pressure difference between the upstream and throat section as seen. The velocity in the throat section is 10 m/s. What is the velocity (m/s) in the upstream pipe?
The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m3/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid‐point of the pipe). SN=21
In the tank-pipe-tank system given in the figure, water flows from A to C in horizontal pipes. Darcy friction factor in A-B pipe is 0.040, pipe diameter is 0.5m, pipe length is 1km and speed is 2m / s. Darcy friction factor in B-C pipe is 0.015, pipe diameter is 1.2m, pipe length is 20km. The gravitational acceleration is 9.81m/s2. There is no operational hydraulic head at point C. Which of the following is the minimum required vertical elevation between free water surfaces, H for running this system?