n) What is the flow direction? (Explain why) b) What kind of machine is at A? (Explain why)
Q: PROBLEM 5 Consider a steel pipe of inside diameter of 10.02 in having in it an open globe valve (K =…
A: Given, Diameter of the pipe D =10.02 in =0.835 ft. Length of the pipe L=100 ft. Discharge Q=5…
Q: At any given time, the flow rate through each compartment will differ from the others. Why?
A: Solution: The flowrate in every compartment will be different from the others because each…
Q: wo pipes 1 and 2 of the same length and diameter are connected in parallel. If f2 = 0.9f1, the flow…
A: solution Given friction in pipe 1 =f1friction in pipe 2=f2and f2=0.9f1as the pipes are parallel head…
Q: A water tank is 30 ft in diameter and the normal depth is 25 t. The outlet is a 3-in horizontal pipe…
A: Given: The diameter of the tank is 30 ft. The normal depth is 25 ft. The diameter of the outlet pipe…
Q: type of flow is obtained by
A: To find : Name of flow that is obtained by superimposing 2 definite flow type.
Q: Problem 3: Water flows through a 100 mm diameter pipe at velocity of 4.5m/sec. Find the discharge.…
A: Q=A V Find reynolds no. for second q.
Q: Two wells are located at points A and B respectively. Point C is the middle point between A and B.…
A: point C is at mid of well A and Well B when only well is pumped out then drawdown at C is 5 inches
Q: Flowing in a 2.5-in.-diameter a diameter of 5 in., calculate the reduced velocity. pipe at 60…
A: Given:initial pipe diameter, d1=2.5 infinal pipe diameter, d2=5 invelocity of water flow, v1=60 ft/s
Q: flowing through a smaller pipes are 25, 15, and 12 L/min, what is the flow rate in the 1.9 cm pipe?…
A:
Q: PROBLEM 6 A 3-ft-diameter welded steel pipe (f = 0.0135) is carrying 15 cfs of water at 60°F. At…
A:
Q: let of the pump. Use Pipe Flow Expert for your analysis.
A: Given:- temperature=80 degree C rate=475L/min To find:- pressure at inlet of pump
Q: Problem 1: Two pipes 1 and 2 having the same length and diameter are in parallel. If the flow in…
A:
Q: what is the velocityof flow in the 4"-diameter pipe in ft/s.
A: given-a pipe diverging pipe with diameter 3" at one end and 4" at other end. required- to find the…
Q: ng rate of flow in open pipe like e.
A: To find : Whether the statement is true or false.
Q: 5. An example of common hydraulic jump is a) Surge tank b) Pump c) Sink d) Air cooler
A:
Q: Q2 Water flows from reservoirs A and B to point C (discharge to atmosphere) through pipes 1 and 2 as…
A:
Q: A pipe carries water at a flow rate of 90 L/s. Determine the minimum inside diameter so that the…
A: Given data : Flow rate (Q)=90 l/sVelocity of fluid (Va)=3 m/sVelocity of fluid (Vb)=2 m/sVelocity of…
Q: A cylindrical tank has a radius of 5 ft and a height of 13 ft. Set up an integral to determine how…
A:
Q: What volume of flow in ft3/s will pass a 10 inch new cast iron pipe with a head loss of 13 ft per…
A:
Q: A pipe 300 m long is to convey 600 liters per second of water between two reservoirs. If the…
A:
Q: n the chamber shown, section 1 has a diameter of 4 inches and flow rate of 2 ??^3/s . Section 2 has…
A:
Q: two pipes 1 and 2 of the same length and diameter are connected in parallel. if f2=0.984f1, the flow…
A:
Q: Two people are arguing on the flow regime of water in a certain trapezoidal canal with the following…
A: Q = 0.09m3 /s
Q: A smooth pipe of diameter 200 mm carries water. The pressure in the pipe at section 'S,' (elevation:…
A:
Q: A 3-inch diameter pipe is connected to a 4-inch diameter pipe If the the velocity of flow in the…
A: To find the velocity in the 3 in. Diameter pipe and flow rate.
Q: Refer to Fig 2 Find the flow rate in m3/sec/m length (at right angles to the cross section shown)…
A: Given:- Depth of soil layer (H) = 5 m The elevation head (H1)=2.8 m Total head (h) = 3.1m, The…
Q: A 100-mm diameter pipe is connected to a 75-mm diameter pipe. If the velocity of flow in the 100-mm…
A: Solution Given that The velocity of flow in 100 mm pipe is= 2 m/s
Q: 3. A discharge of 100 gpm flows in a 6 inch diameter pipe. The pipe neck's down to a 4 in diameter.…
A: Discharge Q=100 gpm=100 cm3/minutedia of pipe d1=6 inch=15.24 cm, Area A1=π4×15.242=192.11 cm2…
Q: A pipe line consists of successive pipes with different sections: 380-mm, 300-mm, and 250-mm pipe.…
A: This question is related to the Fluid Mechanics.
Q: Calculate the peak flow rate generated
A: HYDROLOGY: Option a
Q: Calculate flow, velocity, and headloss in each pipe and pressure at point B in ft, if supply…
A:
Q: Conssier the steady flow in a water pipe joint shown in the diagram. The areas are: A= 0.2 m. Az =02…
A:
Q: Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a…
A:
Q: Glycerine (SG = 1.26) flows through a pipe AB 48" in diameter at 10 fps and then passes through a…
A:
Q: Water from a pipeline is diverted into a weigh tank for exactly 15 min. The increased weight in the…
A: Flow rate = increase in weight / time =4765/15=317.67 lb/min 1lb/min=0.12 gpm Ie flowrate…
Q: Below, a jet wa diameter of 2 ntaining a hole of diameter 8 cm. A portion ed towards the…
A:
Q: Water is flowing in a 300 mm circular pipe with a discharge of 0.250 m/s. Find the Reynold's number…
A: Given data: D=300 mm=0.3 mQ=0.250 m3/s kinematic viscosity for water: ν=9.3157×10-7 m2/s
Q: A circular tank of diameter 1.5 m contains water up to a height of 4 m. An orifice of 40 mm diameter…
A:
Q: Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a…
A:
Q: An oil (s.g=0.85) and viscosity of 1.8 x 10−5 m2/s flows in a 10cm diameter pipe at 0.50L/s. Is the…
A: Laminar flow - It is a smooth flow of liquid particles in layers. The fluid follows a regular path.…
Q: There is the system shown in Figure 1, in which there are two sharp edged type inputs and a sudden…
A: Step 1
Q: Water flows through a one-inch diameter pipe at a velocity of 14.4 ft/s. The pipe divides into two…
A: Solution:Diameter of pipe (D) = 1inch = 0.08333ftVelocity of pipe (V) = 14.4 ft/sec∴ The rate flow…
Q: State the different steps with pictures if possible the way the vane pump can be repaired.
A: Answer - Hydraulic and pneumatic systems, including vane pumps, are repaired and maintained at…
Q: A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The…
A:
Q: 10. What is the function of a surge tank? a) It causes water hammer b) Produces surge in the…
A: What is the function of a surge tank?a) It causes water hammerb) Produces surge in the pipelinec)…
Q: A certain jet fuel has a kinematic viscosity of 1.2 x 10-6 m2/s. If the fuel is being delivered to…
A: kinematic viscosity, = 1.2 * 10-6 m2/s. Discharge, Q= 200 L/ min. Diameter of pipe, D = 22.1 mm =…
Q: Water (ρ = 1000kg / m3, μ = 10-3Pa.s) flows at a speed of 1.6m / s (Reynolds number Re = 0.8 105) in…
A: Given: The density of water is 1000 kg/m3. The dynamic viscosity is 10-3 Pa.sec. The flow speed is…
Q: Water is flowing in a 2.5-in.-diameter pipe at 60 ft/sec. If the pipe enlarges to a diameter of 5…
A: Given: velocity Diameter To find: Reduced velocity
Subject : Fluid
Please explain clearly
Step by step
Solved in 2 steps
- Calculate the head loss in a circular concrete pipe flowing half filled.The diameter of the concrete pipe is 1.5 ft , length is (1000/36)ft and flow velocity is (150/36)ft/sec.For the pipe network shown in figure 2, determine the corrected flow in pipeline CD and BC. For the head loss hf=kQ^2, k valves for each pipe flow are as follows: kAB =kCD =1.0 , kAC =kBD =2.0, kBC =3.0Quick. A tube has a diameter of 30 inches and a roughness modulus of e equal to 1.5 * 103 feet. Find the minimum velocity that makes the flow completely turbulent
- Richard Equation studies the relation between? A- Hydraulic conductivity and time. B- Discharge, hydraulic conductivity and time. C- matrix potential head and hydraulic conductivity. D- matrix potential head and time. What is the correct answer above???A parallel pipe net work connects the bottom of two reserviors. The head difference between the reserviors is 20 m. All three pipes have a ks value of 0.052. The lengths of the pipes are 70, 65 and 100 m and the diameters are 0.4, 0.35 and 0.5 m, respectively. Determine the velocity in each of the three pipes.Oil (SG = 0.89), with a kinematic viscosity of 0.007 ft2/s, flows in a 3-in.-diameter pipe at 0.049 ft3/s. Determine the head loss per unit length of this flow.
- Write legibly Complex Pipeline System_Parallel Pipes 1. The pressure heads at junctions A and E are 70.0 m and 46.0 m, respectively, in the given parallelpipe system shown in the figure. Theflow rate of water entering junction A is 0.30 cms. Assuming that the Hazen – Williams roughness coefficient C = 120 for all pipes, determine the flow rate through each branch of the loop. For the solution, use the Hazen – Williams formula. Answer: a. Pipe ABE = _______________________ cmsb. Pipe ACE = _______________________ cmsc. Pipe ADE = _______________________ cmsDetermine the flow rate of pipe 2 and pipe 3 show your complete solutionA 200 mmФ pipeline whose length and friction factor (f) are 2.5 km and 0.018 respectively connects two tanks A and B. Assuming minor loss to be 10% of friction loss, and reservoir A 15 m higher than B, find the rate of flow * a. 0.03426 m³/s b. 0.05426 m³/s c. 0.04426 m³/s d. 0.06426 m³/s
- Three pipes of different lengths and diameters connected in series as shown discharges 0.16 m³/s. If the roughness coefficient ? = 0.012 and disregarding minor losses, determine a.) the head loss (m) in each pipe and b.) the diameter (mm) of an equivalent single pipe that could replace all the three pipes.1. Determine the flow rate at pipe 1 2. Determine the flow rate at pipe 2 3. Determine the flow rate at pipe 3DIFFERENT QUESTION FOR REVISON-EXAMINATION Additional Questions: (1) A fluid of constant density flows at the rate of 15 Liters/ sec along a pipe AB of 100 mm diameter. This pipe branches at B into two pipes, BC and BD each of 25mm diameter and a third pipe BE of 50mm diameter. The flow rates are such that the flow through BC is three times the flow rate through BE and the velocity through BD is 4 m/s. Find the flow rates in the three branches BC, BD and BE and the velocities in pipes AB, BC and BE. Water is flowing through a pipe with a velocity of 7.2 m/s. Express this velocity as velocity head in meters of water. What is the corresponding pressure in kN/m2. (2) A pipe of 150mm bore is delivering water at a rate of 7500dm3/min at a pressure of 820 kN/m2.It connects by a gradually expanding pipe to a main of 300 mm bore which runs 3 m above it. The main is designed to withstand a maximum pressure of 814 kN/m2. Neglecting loses due to friction determine if the main will fail or…