ne Instruction fetch phase ends A. Placing the data from the address in MAR into MDR B. Placing the address of the data into MAR C. Completing the execution of the data and placing its storage address into MAR D. Decoding the data in MDR and placing it in IR 7. The signal sent to the device from the processor to the device after receiving an interrupt is: A. Interrupt-acknowledge B. Return signal C. Service signal D. Permission signal

ne Instruction fetch phase ends A. Placing the data from the address in MAR into MDR B. Placing the address of the data into MAR C. Completing the execution of the data and placing its storage address into MAR D. Decoding the data in MDR and placing it in IR 7. The signal sent to the device from the processor to the device after receiving an interrupt is: A. Interrupt-acknowledge B. Return signal C. Service signal D. Permission signal

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

1- Write the pseudo-code for the timer interrupt routine to implement time-sharing assume there is an instruction dispatch to invoke the CPU scheduler to select a new job from the ready queue.
What is a transmission gate? Draw its circuit circuit diagram. How does it operate? What is the need for a transmission gate? What is it disadvantage?
Question 1: a. State the names of the architectures model used in microprocessor and microcontrollers architectures? b. State the multipurpose functions of port 3.0 with the symbol, description and pin configuration in microcontroller? c. Define timer and states the functions of its modes of operations?
In a multibyte addition program, when must you use the ADD instruction? When must you use the ADC instruction?
Design a serial adder using the following: Explain the operation briefly, list thestate table (must include present state, inputs, next state, output and flip-flopinputs) and draw the logic diagrama. Using D flip flop, shift registers and necessary logic gatesb. Using JK flip flop, shift registers and necessary logic gates
4) Draw the logic diagram for a modulus-18 Johnson counter. Show the timing diagram and write the sequence in tabular form.
If the current value of the stack segment register and stack pointer are C00016 and F F0016, respectively, what is the address of the current top of the stack ?
In a simple copy machine, a stop signal, S, is to be generated to stop the machine operation and energize an indicator light whenever either of the following conditions exists: (1) there is no paper in the paper feeder tray; or (2) the two micro-switches in the paper path are activated, indicating a jam in the paper path. The presence of paper in the feeder tray is indicated by a HIGH at logic signal P. Each of the micro-switches produces a logic signal (Q and R) that goes HIGH whenever paper is passing over the switch to activate it. Design and build the logic circuit to produce a HIGH at output signal S for the stated conditions, and implement it using the two-input NAND chip.
In a simple copy machine, a stop signal, S, is to be generated to stop the machine operation and energize an indicator light whenever either of the following conditions exists: (1) there is no paper in the paper feeder tray; or (2) the two micro-switches in the paper path are activated, indicating a jam in the paper path. The presence of paper in the feeder tray is indicated by a HIGH at logic signal P. Each of the micro-switches produces a logic signal (Q and R) that goes HIGH whenever paper is passing over the switch to activate it. (3) Regardless the state of the previous two statements the stop signal is active if there is no internet connection to the machine or if the inside temperature sensor is active (This sensor is active if the inside temperature of the machine reaches a certain threshold temperature). Design and build the logic circuit to produce a HIGH at output signal S for the stated conditions.
What are the minimum and maximum propagation?delays for 1 gate for a 7408 chip? 7402 chip? 7404chip? 7432 chip?
2 (a) Determine the control word ICW2 require for PIC controller so that IRQ0 to IRQ7 correspond to type numbers 30H to 37H , specify the memory location from which the processors will fetch interrupt vectors.
Q1: What is Interrupt? Describe different types of Hardware and Software Interrupts.