AAlal TorttQuestion 14Calculate the maximum stress in the diagram below, considering stress concentrations.1.50-mm radius42-mm dia.30-mm dia.Axial tensile force 30.3 kN

Given Diameter, D = 42 mm d = 30 mm Radius, r = 1.50 mm

Answered: ne max stre33 1.50-mm 42-mm dia. 30-mm…

Engineering

Mechanical Engineering

ne max stre33 1.50-mm 42-mm dia. 30-mm Axial tensile force 30

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Related questions

Q: Determine stress in rod

A: Given data : Length (L)=5 mArea (A)=100 mm2Force (F)=10 KN

Q: The state of stress at a point in a loaded member is shown in Fig. 23.1. The magnitude of maximum…

A: Data given-

Q: A steel bar has three axial loads applied as shown in Fig. Draw an axial force diagram for the bar.…

A: Firstly find the support reaction at A. Apply horizontal equilibrium of the system,

Q: Findl the Max. stress on the rivet CapPer steel 下 25mm 50 mm AT= 50°C divt = dy= 11 Hm/mċ こ 20 mm…

Q: 1.25 kN 220 300 Bearings at B and C act as simple supports A 300 550 Dimensions in mm

Q: Explain the Mohr’s circle for stress and write down the procedure of drawing Mohr’s circle and…

A: Mohr's circle: Sign convention,

Q: find the bearing stress between bolts and plate 10/-.. 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN…

A: Given data diameter of bolt (d) = 10 mm thickness of plate (t) = 8 mm Load acting on the plate…

Q: If load P = 20.1 kips, determine the normal force in bar (1).

A: given data: P = 20.1 kips To find: normal reaction force from point D, RD = ?

Q: Apply Mason Rule (S&P) to block diegron below. кле (бар) то e(s) Git H₂P G Hs H₂ ((s) H₁ 62 H₁ бу…

Q: A1 Vi 70 kPa Flange Fx V2 A2

A: Newton's second law states that the rate of change of linear momentum is equal to force. Momentum is…

Q: What is the value of minimum stress? (Principal stress) A 4.34 MPa B) 3.43 MPa 5.44 MPa D 2.43 MPa

Q: 2 kip/f 18 kip ft F6-3

A: Solution: M=18kip.ft w=2kip/ft Shear force in functions of x can be given as, Fx=-wx ( downward…

Q: Question 1 a = 2.1m (1) c=2m b=3./m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN…

Q: 100 mm 300 mm 100 mm 400 N 400 N B 250 mm A 150 mm -500 mm- 4) If member ABC supports the shown…

Q: m=0,015s 5 Steoby Slote, Aiso try Tour =Tia fout = 1,403 kfa RSI5B RSISB Tost = 18°C Tim? Pin= 406…

A: In first case, mass flow rate is 0.015 kg/s. It can be seen that there is no pressure change in…

Q: terial of piston rings Grey cast ird wable tensile stress = wable radial pressure on cvlinder = 0.03…

Q: Determined as the lowest load considering all of the allowable compressive load of spar, shear…

A: Considering the spar, Compressive force = P Let the diameter of spar = D The allowable compressive…

Q: ds kN. P= 100 KN 500 mm

Q: t, f true strain:

A: Given- Engineering Strain = 0.5 To calculate True Strain______

Q: toed et hing ? hing= 20 KN/m

Q: Acircular hottow rod of do=50 mm and Kagi=05is subjected to F=D20 KN the tensile stress…

Q: 8 kN 8 kN 2 kN-m 30°7 В 600 500 600 600 mm mm mm mm

A: Given :- To Find:- Support reactions at point A and B

Q: ximum tensil X1

A: given:length l=400mmthickness b=20mmdepth d=80mm

Q: 10/10 find the shear stress in bolt in pin A 60 kN 4 M 3 BOLT DIA 20 MM A 50 kN PIN A アナナ 2 M

Q: 0.125" O Match each item to a choice: Maximum Value (P) Rivet diameter " Allowable stress: Rivet 10…

Q: The assembly consists of three disks A, B, and C that are used to support the load of P. The load P…

A: Given data

Q: 3 m 1.5 m Ta Aluminum Steel. 75 mm dia, T=1.0 kN m G-28 GN/m2 50 mm dia

Q: Q1- Show the nonzero stress components on the A, B, and C faces of the cube in Figures below: 100…

Q: 2. (practice problem for Exam 1) Find out the normal stress throughout the bar. - Hint: you should…

Q: principal str

A: given: What is principal stress?

Q: Meckenieal Design EnginziNG Calculate the maximum tensile stress in the bracket as shuwn beln. G0 mm…

A: L=400 mmCross section =80 mm×20 mmAxial load P=4.2×sin40°=2.6997 KNTransverse load…

Q: Q1. DRAW STRESS STATES いITH A SQLARE ELEMENT エN *Y AXES Label with stress values Q2. DRAW MOHR'S A…

A: Given: Axial load is 200 lbs. Torque applied is 250 lbs-in. Diameter of the rod is 2 in.

Q: man value of axial force and corresponding stress values. an value of torque and corresponding…

Q: Wi Wz _F STEM PART 1 TAB TAB STEM TAB TAB PART2 BY NC SA 2014 Michael Swanbom Dimensions: WĄ W2 W3…

A: Stress is the ratio of force and area.

Q: Using whatever method you choose, find the force in member BG. 20 kips D 40 kips 18' – 0" E 15 kips…

Q: 30° 10 kN 4 m B E 4 m 16 kN -3 m -

Q: The thickness of the plate is t and the diameter of the pin is d. What is the correct area formula…

A: please refer to the detailed solution given below,

Q: Wall 4 m 1000 mm -3 m- D 1000 mm 800 mm A 1000 mm C 1000 mm B 200 KN 150 kN

Q: What is the maximum flexural stress develop? A 60 KN 20 kN/m B 40 kN C D -2m-2m-2 m-4m- 50 kN E 50…

Q: A 0.75 m 1.5 m 2 т А - 300 тт? A = 250 mm? A= 5 mm C D E = 200 GPa

Q: 100 MPa. The hoop stress in MPa is :Select one a. 150 b. 200 C. 50 d. NONE e. 100

A: Let σh = Hoop stress σL =Longitudinal stress=100MPa As we know that σh =pD/2t…

Q: pressore vessel is shown lelow, determine the diameter of the vessel if the ultimate ; Su= 40OMPA…

Q: strain in the cylinder wall at mid-depth

A: Given; Young's modulus=100 poisson ratio= 0.3 of the container material .Find the axial strain…

Q: The free-body diagram of the entire truss is shown. Find the force ly. A Answer: ly= L B L K C L D L…

A: Draw the free-body diagram which is given.

Q: maximum shear stress in the wall?

A: Given data; Inner radius,r=8 mm Wall thickness,t= 50 mm Gauge pressure=4 MPa Determine the maximum…

Q: A 3/8-inch diameter bolt is subjected to a 2,085-lb tensile load. The bolt passes through a very…

Q: down by iS 12 mm wide A A durafumin Calinder head is held Steel bolt each end whieh asSembled, tight…

Q: 30MM 20mm $225MM 8 20MM •A •B •C 5=25EN F=15EN

A: find the stress at point B and what type of stress at point B.

Q: The maximum compressive stress in (MPa)

A: GIVEN:

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
Given the stress cube below, represent the Mohr Circle, demonstrating the stepsfollowing:a) Calculation of main stresses and directions;b) Calculation of stresses in a plane of rotation ?, clockwise;c) Circle of Mohr.
1. At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2 compressive are applied on mutually perpendicular planes. The planes are also subjected to a shear stress. If the greater principal stress is limited to 100 MN/m2 tensile, determine the value of shear stress. Give you answer to 2 significant figures in MN/m2
a) Prime planes,b) Prime stresses, c) Maximum shear stress and thisin the plane of the stressdetermine the normal stress
For the following data, using Mohr's circle of stress and trigonometry, (a) Find the principle stresses and show their sense in properly oriented element and (b) find the maximum (principle) shear stresses with the associated normal stresses and show the results on a properly oriented element.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.