SECTION AAnswer ALL QuestionsPhysical and mechanical properties of civil engineering materials, their behaviour and characteristicsin design and construction works. Answer below questions using your own words and understanding.(a)(i)Design a concrete mix for the following given data:A mean 28-day compressive strength (measured on standard cubes) of 45 MPaSlump = 40 mm, Uncrushed aggregate with maximum size of 20 mmSpecific gravity of aggregate = 2.64Fine aggregate passes through the 600 µm sieve = 48%No air entrainment required, ordinary Portland cement to be used.[Use supplied charts and table to get required values]

Answered: Image /qna-images/answer/c13c1b73-e78a-4b19-b858-46a9d9e745f1.jpg

nical properties of civil e action works. Answer be a concrete mix for the fc 28-day compressive str- 40 mm, Uncrushed agE gravity of aggregate %3D regate passes through tE atrainment required, ord plied charts and table to

nical properties of civil e action works. Answer be a concrete mix for the fc 28-day compressive str- 40 mm, Uncrushed agE gravity of aggregate %3D regate passes through tE atrainment required, ord plied charts and table to

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Designing a concrete that will be exposed to groundwater, the chemical analysis of which is given in Table 1. is requested. a) For 1 m3 of concrete, assuming the air gap is 1%, according to the relevant impact class specified in TS EN 206 Calculate the amount of material needed. (Maximum grain size of A1, A2, A3 aggregates to be used in the mixture) has a diameter of 16 mm and is in SDYK state, and the physical properties and mixing ratios of the aggregates are given in Table 2.) b) The ratio of cement kneading water to be used in production is 28%, volumetric shrinkage of cement paste Calculate the shrinkage that will occur in the concrete, assuming that the absolute volume of cement is 1%. from shrinkage Find the tensile stress that will occur in the concrete due to Whether cracks will occur in the concrete due to shrinkage, Considering the static elasticity modulus (secant modulus) of the concrete given below in the “stress-strain” diagram. take it and check it. Note: In the…
For concrete production, we mix 625 kg of fine aggregate and 830 kg of coarse aggregate. The fine aggregate has a moisture content of 2.3% and absorption of 3.2%, whereas the coarse aggregate has a moisture content of 1.5% and absorption of 2.8%. Calculate the amount of water required to increase the moisture contents of both fine and coarse aggregate to reach absorption?
500 gm oven dry fine aggregate was tested to find its physical properties. The output from the test was as follows: SSD = 510 gm, mass of the vessel full of water = 1200 gm, mass of vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm, Apparent specific gravity= 2.5 . The grading of the fine aggregate is in the table below. Answer the followings:
A mix design requires 1160 kg/m3 of coarse aggregate (in dry condition), 599 kg/m3of fine aggregate (in dry condition) and 148 kg/m3 of water. The absorption capacityof the coarse aggregate is 0.4 % while the moisture content is 1.5%. The absorptioncapacity of the fine aggregate is 0.4 % while the moisture content is 4%. Pleaseanswer the following questions based on information given. a. What is the amount of Moist Coarse Aggregate? b. What is the amount of SSD Fine Aggregate? c. What is the amount of Moist Fine Aggregate? d. What is the amount of water after adjusting for moisture?
Read the question carefully and give me right solution according to the question. If you don't know the solution please leave it but don't give me wrong solution. Dry weight of coarse aggregate, fine aggregate and water for 1 m3 of one type of concrete requires 1100 kg, 680 kg and 175 liters, respectively. From laboratory test for, it is determined that absorption content of coarse and fine aggregates is 0.5% and 1.25%, respectively. Meanwhile, moisture content of coarse and fine aggregate is 0.75% and 1.0%, respectively. Determine weight of coarse aggregate, fine aggregate and water for one batch with volume of mixer of 800 liter.
500 gm oven dry fine aggregate was tested to find its physical properties. The output from the test was as follows: SSD = 510 gm, mass of the vessel full of water = 1200 gm, mass of vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm, Apparent specific gravity= 2.5 . The grading of the fine aggregate is in the table below. Answer the followings: 1-Moisture content % is 2- The mass of oven dried sand is
Specific Gravity and Absorption of Coarse Aggregates What are the possible discussion of observations for specific gravity and absorption of aggregate to observed values?
A contractor claims that the mean compressive strength for a concrete mix is 32.4 MPa and that it has a standard deviation of 2.8 MPa. If you break 16 cylinders and obtain a mean compressive strength of 30.3 MPa, would you believe the contractor’s claim? Why? (Hint: Use statistical t-test.)
Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes (100 x 100 x 100mm) and 10 prisms (500 x 100 x 100mm), find the mass of each material based on the aggregate conditions in Table 2.
Q. Using the British methods, design a concrete mix to bear an average compressive strength of 35 MPa at 28 days, to cast a room slab with the following dimensions (5 width x 4 length x 0.2 depth m) and 200 mm space distance of reinforcement. Consider the following properties: o Cement used is type I Portland cement ® Required slump = 30 — 60 mm o Coarse aggregate: ® Crushed rocks * Maximum size of 40 mm, e The fine aggregate: * Crushed rocks = Falls in zone 3 o Assume zone A for figure 1 o AssumeK = 1.64
A concrete mix includes the following ingredients per cubic meter: a. Cement = 400 kg b. Water = 176 kg c. No admixture Table P6.30 shows possible changes that can be made to the mix ingredi- ents. Indicate in the appropriate boxes in the table what will happen in each case for the workability and the ultimate compressive strength as increase, decrease, or approximately the same.
lease type your solutions in the box below. Answers without solutions will not have any marks. Students in the materials lab performed the specific gravity test and bulk unit weight and voids of aggregate on a sample of coarse aggregate and obtained the following data: Mass of oven dried aggregate: 951 g Mass of aggregate submerged in water: 603 g Mass of saturated surface dry aggregate: 993 g Find: Bulk dry specific gravity of aggregate. Find the absorption of aggregate. If the dry rodded unit weight of aggregate found to be 1695 kg/m3 , calculate the percent voids between aggregate particles in this test. We blend this aggregate with other aggregate with bulk dry specific gravities of 2.23. Calculate the bulk dry specific gravity of the blend if the blend proportion is 40:60.