NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Refrigerant-134a enters the coils of the evaporator of a refrigeration system as a saturated liquid-vapor mixture at a pressure of 140 kPa. The refrigerant absorbs 200 kJ of heat from the cooled space, which is maintained at -10°C, and leaves as saturated vapor at the same pressure. Problem 07.025.b - Entropy change of the cooled space in an evaporating process Determine the entropy change of the cooled space. (You must provide an answer before moving on to the next part.) The entropy change of the cooled space is [ kJ/K.

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Refrigerant-134a enters the coils of the evaporator of a refrigeration system as a saturated liquid-vapor mixture at a pressure of 140 kPa. The refrigerant absorbs 200 kJ of heat from the cooled space, which is maintained at -10°C, and leaves as saturated vapor at the same pressure. Problem 07.025.b - Entropy change of the cooled space in an evaporating process Determine the entropy change of the cooled space. (You must provide an answer before moving on to the next part.) The entropy change of the cooled space is [ kJ/K.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.1DP

See similar textbooks

Similar questions

A Three stage
Water melts as temp increases because : - chemical potential of the liquid is lower than that of gas - liquid and solid form eutectic mixture -chemical potential of the liquid and solid become equal
Pls. Answer thank you! The evaporative condenser of an ammonia refrigeration plant has a water flow rate of 100 kg/s and enters a natural draft cooling tower at 43 °C. The water is cooled to 30 °C by air entering at 27 oC db 24 °C wet bulb. The air leaves the tower as 90% RH and 32 °C db. Calculate the percent of make-up water needed the tower. At 27 °C db and 24 °C wb: h = 72.5 KJ/kg, w = 0.0178 At 90% RH and 32 °C db: h = 102 KJ/kg, w = 0.0275
3) If the measurement parameters of a refrigeration machine are known, the amount of heat for liquid refrigerant (mix) when it enters the evaporator is 650 Btu/lb, the amount of heat for vapor refrigerant after it comes from the evaporator is 950 Btu/lb, and the amount of heat for superheat refrigerant after being compressed is 1280 Btu/lb. lb. Calculate the efficiency of the refrigeration machine?
It is based on the centralised production of chilled water and its distribution for a wide range of indoor air cooling purposes. Consumer Substation Thermal Energy Storage Tanks Hot Plate heat exchanger District Cooling
CPE614: PROCESS INTEGRATION
Problem 2 – Heat Pump Thermodynamic Analysis Refrigerant-134a enters the condenser of a residential heat pump at 800 kPa and 50°C at a rate of 35 L/min and leaves at 750 kPa subcooled by 3°C. The refrigerant enters the compressor at 200 kPa superheated by 3°C. Neglecting changes in kinetic and potential energy and any stray heat transfer, please answer the following. a. Create a schematic of the cycle, use the same numbers used in your textbook for the inlet and exit states of each device, and include the energy exchanges between the cycle devices and the surroundings. b. Sketch the cycle processes on a T-s diagram. c. Determine the isentropic efficiency of the compressor. d. Compute the rate of heat supplied to the heated room. e. Determine the COP of the heat pump.
An 500-HP engine with a thermal efficiency of 30% is using a remote radiator which absorbs 20% of the heat supplied to the engine. Cooling system with cooling tower is used with a cooling range of 5°C. The temperature rise after passing the remote radiator is 10°C. Air enters the cooling tower at 30°C dry-bulb; 20°C wet-bulb temperatures and leaves the tower at 38°C & 65%RH. Make a schematic diagram of the system, the process in the provided psychrometric chart and calculate the following: (a.) The amount of cooling water for the engine, kg/min; (b.) The water flow rate in the cooling tower in liters per hour; and (c.) If the heat absorbed by air is 5% of heat absorbed by the cooling tower water, what is the air flow needed in cu.m/hour.
Subject: thermodynamics In a gas turbine generating set, two stages of compression are used with an intercooler between stages. The HP turbine drives the HP compressor, and the LP turbine drives the LP compressor and the generator. The exhaust from the LP turbine passes through a heat exchanger which transfers heat to the air leaving the HP compressor. There is a reheat combustion chamber between turbine stages which raises the gas temperature to 600 ?C, which is also the gas temperature at entry to the HP turbine. The overall pressure ratio is 10/1, each compressor having the same pressure ratio, and the air temperature at entry to the unit is 20 ?C. The heat exchanger thermal ratio may be taken as 0.7, and intercooling is complete between compressor stages. Assume isentropic efficiencies of 0.8 for both compressor stages, and 0.85 for both turbine stages, and that 2% of the work of each turbine is used in overcoming friction. Neglecting all losses in pressure, and assuming that…
A cascade system is to be designed to attain a temperature of 213K in an environment of 313K. The refrigerant of the high temperature side is R-134-A and that for low side is R-134-A. The condensing temperature of low side is 5K above the evaporator temperature in the cascade. Compute A.Cop. B.pressure Ratio. C.Mass flow rates of each refrigerant. D.Volume flow rate per TOR. with TS Diagram Using this Steam Table:https://docdro.id/VkxK8WH
The catalogue for a refrigerant 22, four-cylinder, hermetic compressor operating at 29 r/s. a condensing temperature of 40 °C and an evaporating temperature of -4 °C shows a refrigeration capacity of 96.4 kW. At this operating points the motor (whose efficiency is 90 percent) draws 28.9 kW. The bore of the cylinders is 87 mm and the piston stroke is 70 mm. The performance data are based on 8 °C of subcooling of the liquid leaving the condenser. Compute 3.1 the actual volumetric efficiency and 3.2 the compression efficiency.
What is the heat output, in Btu/h, of a terminal unit with a T of 10F and a water flow rate of 5 gpm?