NPUT (CL) 1) INPUT: X1: X1: X2: X2: x3: 2) 5. Consider the circuit below, consisting of three R-S flip-flops connected as T-flip-flops. Required: 1) Draw in the indicated spaces below, the diagrams of the outputs 21, 22, 23, as well as of T1, T2, T3. Important: The outputs 21, 22, 23 have all initial values of 0, which gives their complements, 1, 2, 3 initial values of 1. 2) Describe in one sentence what this circuit could be used for. S CL CR X1 X1 U X1 S CR CL X2 X2 X2 S CL R X3 X2 X3

NPUT (CL) 1) INPUT: X1: X1: X2: X2: x3: 2) 5. Consider the circuit below, consisting of three R-S flip-flops connected as T-flip-flops. Required: 1) Draw in the indicated spaces below, the diagrams of the outputs 21, 22, 23, as well as of T1, T2, T3. Important: The outputs 21, 22, 23 have all initial values of 0, which gives their complements, 1, 2, 3 initial values of 1. 2) Describe in one sentence what this circuit could be used for. S CL CR X1 X1 U X1 S CR CL X2 X2 X2 S CL R X3 X2 X3

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

State diagram given for a sequential circuit with 3 flip-flops A,B,C and 1 input X and 1 output Y. Design this circuit with D flip-flops using binary coding. (You should set unused states as "don't care".)
*Please make sure the outputs are correct, they must look like: R1=10 ohms and i1=0.5AR2=20 ohms and i2=0.25AR3=100 ohms and i3= ___AR4=125 ohm and i4=___AR5=200 and i5=___A
Build the following function using only 8x1 Mux: F(a,b,c,d,e) = ∑ (0, 4, 8, 16, 17, 20, 22, 24, 25, 31) [NB: Must show MSB & LSB] [NB: The circuit should be cost efficient. Meaning, try to use lowest number of ICs possible for an optimum design]
Encode the function f(w, x, y, z) = Σm(0, 1, 3, 4, 7, 6, 9, 11, 10, 13, 14). You must label your product terms and use the left-most and top-most input/output lines for any required feedback forcredit
4. The following figure shows the four-bit Adder-Subtractor. Your inputs for this combinational circuit are A = 5, B = 6 and M = 1. What is the outputs S3, S2, S1, and S0? You have to show how to get the outputs by indicating each carry bit. (Note: You should show all the steps to receive full credits)
A. Write the Boolean equation directly from the following circuit. B. Create the truth table for the circuit above.
Draw the transistor level of the following function
Truth Table : (Write a python program for the following below) You must produce all seven truth tables (AND, OR, NOT, XOR, NAND, NOR and XNOR) and an eight truth table for (A ∨ B) ꚛ C = Q, using the gates logic from the Python Logic Code: AND, OR, NOT & XOR Assignment. Each gate must be a function. The output should look like this:
Q#01. A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation are JA = B’y + Bx’ KA = B’xy’ JB = A’x’ KB = (A’)’ + x’y’ Z = Axy + B’xy’ Draw the logic diagram of the circuit. Tabulate the state table. Derive the state equations for A and B
a. Draw a circuit which produces Sum and CarryOut from inputs A and B (this circuit is known as a half adder). You should use exactly one AND gate and one XOR (exclusive or) gate. b. Give the truth table for a full adder (which incorporates a carry-in bit to the sum of A and B):
Design combinational logic for outputting the wait time associated with each state. For example, state 000 has the main street green light on for 15 seconds. The combinational logic for the input 000 would have an output 1111 corresponding to decimal 15. Let the outputs W3, W2, W1 and W0 represent a binary number corresponding to the wait time.
Digital Logic and Computer Design The following picture is a 1-bit ALU that performs AND, OR and addition on a and b or a and not(b). Draw the required gates for the addition box and a truth table for the 1-bit ALU