nts ce The voltage and current of an ac circuit are as follows: e = 141. sin (377t + 10) V and i = 10 cos (377t-30)A. Find the power factor. Select the correct response: 0.46 leading 0.46 lagging 0.64 lagging 0.64 leading Continue > < Previous ts ubedu.ph/student take quiz assignment/start/33008469#

nts ce The voltage and current of an ac circuit are as follows: e = 141. sin (377t + 10) V and i = 10 cos (377t-30)A. Find the power factor. Select the correct response: 0.46 leading 0.46 lagging 0.64 lagging 0.64 leading Continue > < Previous ts ubedu.ph/student take quiz assignment/start/33008469#

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 7PP: Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.

See similar textbooks

Similar questions

A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
Impedance of AC circuit and Admittance of AC circuitSHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN DRAW IT MANUAALYY thNAKSS
Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2 Ohms, L=5 milliHenry, C=200 microFarad, V=70sin(wt) volts. Determine the watts and VARs for the capacitor, resistor, inductor, and source. Also find power factor. Given R1=9 Ohms, R2=1 Ohms, L= 3 milliHenries, and a sinusoidal voltage source of 5 volts amplitude and 60 Hz freqency all in series. Determine the voltage across R1: magnitude (volts), frequency (Hz), and phase (degrees).
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
Three Impedances each of (13 -j16) ohm are connected in mesh across a three-phase 405V ac supply. Determine the phase current, line current, active power, reactive power and apparent power drawn from supply. Current (Ip) phase Line current Teal power reactive powet Apparent power
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
The following phasor diagram is: a. The phasor diagram of SG when it is running at lagging power factor b. The phasor diagram of SM when it is running at leading power factor c. The phasor diagram of SM when it is running at lagging power factor with the existence of RA d. The phasor diagram of IM when it is running at lagging power factor
Calculate the impedance ?? for the maximum average power transfer in the circuit shown in Figure 3. and find the value of the maximum average power transferred to.
Given the following equation i = -4 sin(377t + 65°) and e = 5 cos(377t + 190°). Draw the phasor diagram and solve for the following: a. Element present in the circuitb. Power factorc. Real Power in RMS *round the final answer to four decimal places and label it with correct units.
The measurement made on a transmission line is given by the graphic in the figure. If the line length is 8.4 cm and characteristic impedance is 50 ohms; Find the load reflection coefficient, load impedance, reflection coefficient at the line input.