Nyquist sampling rate is where fm is the maximum frequency of the analog signal sampled. a. greater than 2fm O b. fm O c. 2fm O d. less than 2fm
Q: nd the frequency content of the following analog signal u 2 3.
A:
Q: Gap between the spectral components of sampled signal in frequency domain can be increased by…
A: Gap between the spectral components of sampled signal in the frequency domain is decreased by…
Q: Plot the following signals. Label x-axis with time(s) for continuous time signals, and 'n' for…
A: Required: on matlab
Q: A complex low-pass signal has a bandwidth of 500 kHz. What is the minimum sampling rate for this…
A: A complex low pass signal has a bandwidth of 500khz. What is the minimum sampling rate for this…
Q: A new ADC (analog-to-digital conversion) technique is to be developed for high-quality music…
A: Introduction:
Q: the minimum sampling rate (according to Nyquist frequency) for the signal [ x(t) =2 ? cos 6000 Ttt +…
A: Hello Student. Greetings Hope you are doing great. I will try my best to answer your question. Thank…
Q: What is the Nyquist sampling rate for the band-pass signal with bandwidth of 850 KHz if the lowest…
A: Given data: bandwidth: 850 KHz lowest frequency: 350 KHz To find: Nyquist sampling rate
Q: The Nyquist sampling rate is a. f b. 2f c. 4f d. 6f
A: Given that: The Nyquist sampling rate is a. f b. 2f c. 4f d. 6f
Q: A binary signal is transmitted using Angle modulation. You are located at the receiver and you…
A: Answer: In frequency modulation (FM), the carrier signal's frequency varies in response to the…
Q: The average signal rate of 2BlQ is a. N b. N/2 c. N/4 d. N/6
A: Question The average signal rate of 2BlQ is a. N b. N/2 c. N/4 d. N/6
Q: Q2 An FM wave is given by s(t) = 20cos(8nx106 +9sin (2 nx10³)). Calculate the (a) frequency…
A:
Q: A(n)_________ signal is a composite analog signal with an infinite bandwidth.
A: The digital signal is one which used to represent data as a sequence of discrete values. At any…
Q: For an FM modulator with a modulation index of m = 1, and the given parameters as below. Va(t) = 2…
A: below given the frequency spectrum
Q: The antenna current of an AM broadcast transmitter, modulated to a depth of 60%, by an audio sine…
A: m is modulation index, It is antenna current and It is carrier current. We are given It =12A, m =…
Q: 9-bit binary number
A: Here is the answer which is mentioned below:
Q: Plot the following signals. Label x-axis with time(s) for continuous time signals, and 'n' for…
A: Required:
Q: Round your answer to two decimal places, A signal has a fundamental frequency of 750 Hz. What is its…
A: The relationship between frequency(f) and Time period(T) is: f=1TsoT=1f T=1750=0.001333 s( as…
Q: i To amplify the signals we use a) Attenuators b) Compensator c) Bandwidth d) None
A: The process of increasing the amplitude of a signal is called Amplifying.
Q: Calculate the modulating frequency that causes an FM signal to have a bandwidth of 50kHz when its…
A: - We need to find the correct modulating frequency.
Q: If the highest frequency component in an analog signal is 20 kHz, what is the minimum sample…
A: Frequency: Knowing that, if we tend to decide that the very best frequency we're inquisitive about…
Q: 2. For the given signal, x(t)= 5 + sin(6t) + 2cos(8t),
A: Requirements :- plot on matlab Approach :- Steps :- 1 . take an appropriate time range 2.…
Q: term that refers to infinite no of values in the range is Analog Signal
A: The term that refers to infinite no of values in the range is Analog Signal Reason is explained…
Q: (c) Filtering and sampling. The continuous-time signal x(t) = 100 sinc2 (100t) goes through an ADC…
A:
Q: The Nyquist sampling rate required to sample the signal x(t)= [cos(6000 nt).cos(2000 nt) is equal…
A: Given signal cos(6000πt)cos(2000πt) From the formula cos(a+b)+cos(a-b)=2(cosa.cosb)…
Q: A digital signal can only be sent in baseband if we have a channel. a. low-pass b. bandpass c. low…
A: GIVEN: A digital signal can only be sent in baseband if we have a channel.a. low-pass b. bandpass c.…
Q: Using the Nyquist theorem, calculate the minimum sampling rate for an analog signal with frequencies…
A: Here, I have to provide a solution to the above question.
Q: 4) Frequency Division Multiplexing and Wave Division Multiplexing are the techniques of a) Analog b)…
A: Multiplexing is a process of merging different signals and forming into a single signal, over a…
Q: The output signal from a conventional AM modulator is u(t)= 4 cos(3600pi t) + 24 cos(4000pi t) + 4…
A: The complete answer is given below.
Q: Q7) 1 GHz carrier is frequency modulated by a 10 kHz sinusoid, so that the peak frequency deviation…
A: 1 GHz carrier is frequency modulated by a 10 kHz sinusoid, so that the peak frequency deviation is1…
Q: H.W. 1 Find the Nyquist rate and Nyquist interval for the following signals: 1. m(t)…
A: Answer 1
Q: Nyquist sampling rate is where fm is the maximum frequency of the analog signal sampled. a. greater…
A: The Nyquist sampling rate is the minimum rate at which a finite bandwidth signal needs to be sampled…
Q: Asignal of maximum frequency of 20 kHz is sampled at Nyquist rate. The time interval between two…
A: The time interval is the reciprocal of frequency
Q: A. calculate the Nyquist rate and interval of the following signals 1) x(t) = ¹/47 cos (3000nt)…
A: 1) Given that, x(t) = 14π cos(3000πt) cos(5000πt) ------(1) Now let us assume…
Q: Q6/ Calculate the minimum sampling rate to avoid aliasing when a continuous time signal is given by…
A: I have solved the solution in the step below for any question you may have.
Q: Plot the following signals. Label x-axis with time(s) for continuous time signals, and 'n' for…
A: Matlab code: clc; clear all; % clear all the registers close all; % it will close all the previous…
Q: The technique that is most common to change an analog signal to digital data is a. delta modulation…
A: Given that, The technique that is most common to change an analog signal to digital data is :
Q: Calculate the Nyquist rate for sampling when a continuous time signal is given by x(t) = 5 cos 100tt…
A: This can be solved as follows
Q: A continuous-time signal is sampled with a sampling time interval of 0.0012 sec. then the frequency…
A: Please give positive ratings for my efforts. Thanks. ANSWER
Q: Plot the following signals. Label x-axis with time(s) for continuous time signals, and 'n' for…
A: Matlab code: clc; clear all; % clear all the registers we have close all; % it will closes all the…
Q: (b) What is the discrete-time signal obtained after sampling the analog signal…
A: The Answer is
Q: x(t)=3cos2000πt+5 sin 6000rt+10 cos12,000 t i. What is the Nyquist rate for this signal ii. Assume…
A: 1. The frequencies of the analog signal are F1 = 1KHz F2 = 3KHz F3 = 6KHz The…
Q: Q3 Ideal ADCS and DACS The signal r(t)3 cos(27 fit)+ sin(27 f2t) goes into an ideal ADC, the output…
A: Hey there, I am writing the required solution of the questin mentioned above. Please do find the…
Q: For an FM modulator with a modulation index of m = 1, and the given parameters as below. Va(t) = 2…
A: m=1 there is a carrier component and 3 sets of significant side frequencies.
Q: What is the maximum bandwidth of an FM signal with a deviation of 27 kHz and a maximum modulating…
A: The Carson bandwidth rule is expressed by the relation CBR = 2 (Δf + fm), where CBR is the bandwidth…
Q: In Phase Modulation, the modulation index represents Select the correct response: the ratio of the…
A: Phase Modulation is a process of varying the phase of the carrier signal with respect to input…
Q: Q19/ The information in an analog waveform, with maximum frequency fm=6 KHz, is to be transmitted…
A: The solution for the above given question is given below:
Q: Plot sin wave with frequnecy fm and then the sampling signals at sampling frequencies fs1, fs2, fs3…
A: Write MATLAB code to plot the following signals: sine wave Sampling signal of sine wave at…
Q: 0. The bandwidth of a signal whose highest frequency component is 760024 kHz and whose lowest…
A: Bandwidth: If we have more bandwidth, the data can be send and receive more faster over the internet…
Q: Given an analog signal sampled at a rate of 8,000 Hz, x(t) = 5 cos (2π 1500t), for t≥0, a. sketch…
A: (a) Program code: fs1=8000; %Very high sampling rate 8000 Hz nCyle=1; %cycle 1 t1=0:1/fs1:nCyle*1;…
Q: The modulating frequency of an FM signal, with modulation index 2.5 and maximum deviation of 25 KHz…
A: Modulation Index is the ratio of frequency deviation and modulating frequency
6
Step by step
Solved in 2 steps
- 288. The inverse of the sampling interval is called the a. sampling rate b. delta rate c. baud rate. d. bit rate224. The difference in the delay of the signal may create a difference in a. Phase b. Frequency c. Period d. Decibel284. The technique that is most common to change an analog signal to digital data is a. delta modulation b. pulse code modulation c. sampling d. Quantizing
- A digital signal can only be sent in baseband if we have a channel.a. low-pass b. bandpass c. low rate d. high rate a. low-pass b. bandpass c. low rate d. high rateA digital signal that uses more levels can provide for higher bit rates but less system reliability. Select one: A. True B. False259. The relationship between data rate and signal rate depends on the value of a. data rate (N) b. case factor (c) c. ratio ( r ) d. signal element(s)