I need the answer as soon as possible oBA-Find the maximum power delivered to the load RL at points ab in Fig.(S).0.212 kfl2 kfl280 V32 kn5.6 kng RLFig (5)B- The voltage (vs-10 v) is applied to a series resonant circuit composed of (42)resistance, (16 uF) capacitance and (1H) inductance. Determine:1) The series resonance frequency2) Quality factor3) Band width4) Cutoff frequencies

Answered: Image /qna-images/answer/40e0940f-4e86-4661-af9a-778e9bfc20f6.jpg

Answered: oBA- Find the maximum power delivered…

oBA- Find the maximum power delivered to the load RL at points a,b in Fig (S). 0.21 2 kfl 2 kil 3 2 kl 5.6 kn RL 280 V Fig (5)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) In an RC circuit supplied with AC power, a 500 ohm resistor is used to create a system with a crossover frequency wc =440 rad/s. What capacitance is the capacitor in this circuit? b. If an inductor is to be added to this circuit to make the resonant frequency equal to the crossover frequency, then what inductance must this inductor have? c. If, near a particular time t1, the instantaneous voltage drop over the resistor is given by v(t1)=0.65V cos(440t), then what is i(t1) (the function of instantaneous current with respect to time) for its capacitor? d. What would the Irms value be based on the sinusoidal function you found in part c? (Pick off Ipeak from the function, then plug in to rms equation)
An impedance coil whose resistance and inductance are 18 ohms and 3.82 mH,respectively, is connected in parallel with a series combination of a 5.3 uF capacitorand a variable resistor. For what value of resistance will the circuit be in resonance at1000 cps?
In the circuit in the figure, Vcc= 18 V, Rs1 = 0.9 k2, Rs2 = 0.5 kQ, R1 = 75 kQ, R2 = 15 kQ, RC = 2.2 kQ, RE = 1 k and B = 120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = C = 44 pF and Cce = 11 PF. Accordingly, considering the frequency response of the circuit, what would the high cutoff frequency (fH) be? NOTE-1: The output impedance of the transistor is ro = 20 k and will be taken into account in the calculations. NOTE-2: high frequency dependence of hfe, B. will be taken into account.
In the circuit in the figure, Vcc= 18 V, Rs1 = 0.9 kohm, Rohm = 0.5 kQ, R1 = 75 kohm, R2 = 15 kohm, RC = 2.2 kohm, RE = 1 kohm and B = 120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = C = 44 pF and Cce = 11 PF. Accordingly, considering the frequency response of the circuit, what would the high cutoff frequency (fH) be? NOTE-1: The output impedance of the transistor is ro = 20 k and will be taken into account in the calculations. NOTE-2: high frequency dependence of hfe, B. will be taken into account.
1. An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitanceand resistance should be connected in series with the coil if the power input to the latter is toremain unchanged and the overall power factor is to be unity (in resonance)? The circuit isenergized by a 120 volt, 60 cps source.2. A series RLC circuit has a Q of 75 and a pass band between half-power frequencies of 160 cps.Calculate the frequency of resonance and upper and lower frequencies of the pass band.3. An impedance coil having a resistance of 30 ohms and a 50 cps inductive reactance of 33.3 ohmsis connected to a 125 volt 60 cps source. A series circuit consisting of a 20 ohm resistor and avariable capacitor is then connected in parallel with the coil. (a) for what values of capacitancewill the circuit be in resonance? (b) calculate the two values of line current for the condition ofresonance.4. A parallel-series filter like that of Fig. 13.10b in the scanned copy of the on page 364 is…
A series RLC circuit is operated at a frequency different from its resonant frequency. The operating frequency is such that the current leads the supply voltage. The magnitude of current is half the value at resonance. If the values of R, L, and C are 1Ω, 1H, and 1F respectively, determine the angular frequency (in rad/s).
ı just need fınal aswer In the circuit in the figure, Vcc = 18 V, Rs1 = 0.9 kΩ, Rs2 = 0.5 kΩ, R1 = 75 kΩ, R2 = 15 kΩ, RC = 2.2 kΩ, RE = 1 kΩ and β =120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = Cπ = 58 pF and Cce = 11 pF. Accordingly, considering the frequency response of the circuit, what would be the high cutoff frequency (fH)? NOTE-1: The output impedance of the transistor is r0 = 20 kΩ and will be considered in the calculations. NOTE-2: The high frequency dependence of hfe, that is β, will be taken into account. a. 189,95 kHz b. 617,33 kHz c. 569,84 kHz d. 474,87 kHz e. 332,41 kHz f. 47,49 kHz g. 142,46 kHz h. 712,30 kHz
A series RLC circuit in which R = 1.00 Ω, L = 1.00 mH, and C = 1.00 nF is connected to an AC source delivering 1.00 V (rms). (a) Make a precise graph of the power delivered to the circuit as a function of the frequency and (b) verify that the full width of the resonance peak at halfmaximum is R/2πL.
1. A series RLC circuit has a Q of 75 and a pass band between half-power frequencies of 160 cps. Calculate the frequency of resonance and upper and lower frequencies of the pass band. 2. A 15.9 uF capacitor and a 15.1 mH inductor are connected in parallel. In series with these units are a variable resistor R and an adjustable device X, joined in series. (a) Determine the kind and size of device X (inductance in Henry or capacitance in Farad) when the circuit is connected to a 50 volt 400 cps source and is adjusted to resonance. (b) For the resonant condition, calculate the value of R if the voltage drop across the paralleled units is to be 100 volts. 3. An impedance coil having a resistance of 30 ohms and a 50 cps inductive reactance of 33.3 ohms is connected to a 125 volt 60 cps source. A series circuit consisting of a 20 ohm resistor and a variable capacitor is then connected in parallel with the coil. (a) for what values of capacitance will the circuit be in resonance? (b)…
A 10.0-Ω resistor, 10.0-mH inductor, and 100-μF capacitor are connected in series to a 50.0-V (rms) source having variable frequency. If the operating frequency is twice the resonance frequency, find the energy delivered to the circuit during one period.
Q2.The current versus angular frequency o for a resonant RLC series circuit is given in the graph. The inductance(L) is 20 µ H and the peak voltage(Vo) of AC source is 8V. a) Find Capacitance(C) and Resistance(R). b) What is the phase difference(@) of this circuit at o,=25,000 rad/s?
R= 300 ohm, L= 40 mH, C= 600nF, V(AC)=5 Volt, F= 100 Hz Calculate theoretically the voltages XL (Inductance = Resistance of the coil), XC (Capacitance = resistance of the capacitor), Z (Impedance = Equivalent resistance of the circuit), VL, VC, VLC and the current value I (mA). Also explain the relationship of XL and XC with frequency in two words. Write the relation that gives the resonant frequency.