Obtain a formula for the strain energy U of the statically indeterminate circular bar shown in the figure. The bar has fixed supports at ends A and B and is loaded by torques 2T, and To at points C and D, respectively. (Assume that the shear modulus of elasticity is denoted G, and the polar moment of inertia is denoted Ip.) 27, To B D R R 2

Obtain a formula for the strain energy U of the statically indeterminate circular bar shown in the figure. The bar has fixed supports at ends A and B and is loaded by torques 2T, and To at points C and D, respectively. (Assume that the shear modulus of elasticity is denoted G, and the polar moment of inertia is denoted Ip.) 27, To B D R R 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pulley shown is connected to a bracket with a circular pin of diameter d = 4.5 mm. Each vertical side of the bracket has a width of b = 26 mm and a thickness of t = 2.2 mm. Consider a free body diagram of the pulley with the belt tensions. Solve for the reaction forces Rx and Ry. If the pulley belt tension is P = 660 N, what is the average bearing stress produced in the bracket by the pin?
The conical bearing is subjected to a constant pressure distribution at its surface of contact. If the coefficient of static friction is μs, determine the torque M required to overcome friction if the shaft supports an axial force P.
The pivot bearing is subjected to a pressure distribution at its surface of contact which varies as shown. If the coefficient of static friction is μ, determine the torque M required to overcome friction if the shaft supportsan axial force P.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the slope at A, (c) the slope at B, and (d) the deflection at midspan. Assume that EI is constant for the beam. Let M0 = 45 kN·m, L = 4.5 m, E = 220 GPa, and I = 145 x 106 mm4. Draw a free body diagram of the beam and solve the reaction forces Ay and By. The diagram shows these forces in their positive directions. Your answers may be negative.
S2) The distributed load, which is given as function of q (x) = q0 (2x/3L)2, acts on the ABCbeam given in the figure. The left side of the ABC beam is fixed at A. The weight of the ABCbeam is neglected. Accordingly, find all the reaction forces of beam.Note: In the calculations, the equations available in the tables of the elastic curve cannot beused. In case of using these equations of the elastic curve, the answer will be invalid.
For the beam and loading shown, determine (a) the equation of the elastic curve, and (b) the deflection midway between the supports. Assume that EI is constant for the beam. You can use any method for the beam deflection computation.
3. The beam below is used to support a part of the overhang at the entrance of the building (a). The idealized model for beam with load is shown in (b). Assume that B is roller supported and C is simple supported. (a) Draw shear force (V-) and bending moment (M-) diagrams for the beam. Determine the position and value of maximum bending moment. (b) For the beam, assume HEA 180 for the type of cross section. Calculate the maximum normal stress and the maximum shear stress, and determine where in the cross section the normal and shear stresses are greatest. Utilize Appendix C at the end of the textbook.
If σsafety=140MPa (safety stress) in the beam whose loading condition and cross-section are visible, find the maximum value of the P force, Based on the assumption of Maximum shear stress (Tresca) and deformation energy (Von Mises) theorems. Draw the shear stress diagram for the force P found.
For the beam and load shown in the figure, determine (a) the equation of the elastic curve for section AB of the beam, b) the slope at A, c) the slope at B.
in figure shown the cylinder has a wieght w and radius r , and the coefficient of static friction is the same at A and B ,Determine the magnitude of the largest couple moment can be applied to the cylinder if it is not rotate.
The structure is loaded as shown in the figure. Determine the internal axial force, shear force and bending moment at point C. Also, calculate the internal bending moment at D.(include the FBD)
The individual forces P act on the simply supported beam made of I profile, the dimensions of which are given in the figure. The largest P load that the rod can safely carry,a) Calculate the security conditions such that σallow= 140 MPa, τallow = 70 MPa.b) Calculate for σM = σallow = 140 MPa using the maximum shear stress (Tresca) and Von Mises assumptions