Answered: Of the following process types,… | bartleby

Practical Management Science

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter4: Linear Programming Models

Section: Chapter Questions

Problem 111P

See similar textbooks

Related questions

Question

Of the following process types, ________ has the lowest output variety, and the highest output volume.

A) Assembly line

B) Batch

C) Job shop

D) Project

Expert Solution

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A large office with a copy department, a drafting department with all of the engineers located together, and all of the managers located together in a large suite of offices is an example of: a. An assembly line process b. A batch process c. A project process d. A continuous process Explain incorrect answers also.
An assembly line has 10 serial stations with process times of 1, 2, 3, 4,..., 10 respectively. The process time of the system is: a) 550% of its process cycle time. b) 18.18% of its process cycle time. c) 50% of its process cycle time. d) 100% of its process cycle time.
Why are assembly-line processes usually so much more efficient but less flexible than batch processes? Give three reasons.
A product is completed when 18 tasks are done. These tasks are assigned to 6 workstations (each workstation handling several tasks) in an assembly line set up. All workstations work the same amount of time (= cycle time), and move the (partial) product to the next workstation, and repeat this process. The last workstation generates the finished product. We need 1200 units made every day (= 8 hours). If we run this line with a cycle time of 0.3 minutes, what is the most amount of work (in minutes) that can be done on this product? (Give the answer with one decimal place)
A production process is shown in the figure above. The drilling operation occurs separately from, and simultaneously with the sawing and sanding operations. Welding starts when both drilling and sanding operations have been completed. After welding, a product needs to go through only one of the three assembly operations (the operations are in parallel, where parallel lines perform the exact same operation). Considering the process times, specify the bottleneck(s). Sawing Sanding Drilling Welding Assembly You can choose more than one.
Cycle time should always be between the shortest and the longest task times in a production cycle Select one : a . TRUE b . FALSE
onsider a process consisting of three resources. Assume there exists unlimited demand for the product, and that all activities are always performed in the following sequence. Resource 1 has a processing time of 6 minutes per unit. Resource 2 has a processing time of 3 minutes per unit. Resource 3 has a processing time of 5 minutes per unit. All three resources are staffed by one worker and each worker gets paid $14 per hour. How much idle time does the worker at resource 3 have per unit?
I already find a. I need help with b Bill's Barbershop has two barbers available to cut customer's hair. Both barbers provide roughly the same experience and skill, but one is just a little bit slower than the other. The process flow below shows that all customers go through steps B1 and B2 and then can be served at either of the two barbers at step B3. The process ends for all customers at step B4. The numbers in parentheses indicate the minutes it takes that activity to process a customer. b. What single activity is the bottleneck for the entire process? B what?
A production process at Kenneth Day Manufacturing is shown in the figure below. The drilling operation occurs separately from, and simultaneously with, the sawing and sanding, which are independent sequential operations. A product needs to go through only one of the three assembly operations (the operations are in parallel). A) is the bottleneck. b) The bottleneck time isminutes per unit (round your response to two decimal places). c) The throughput time of the overall system is enter your response here minutes (round your response to two decimal places). D) If the firm operates 8 hours per day, 20 days per month, the monthly capacity of the manufacturing process isunits (enter your response as a whole number).
Suppose you are going to develop a system to plan a graduation ceremony. By using an activity diagram, model the process context for such a system that shows the activities involved in it (booking a place, planing the decoration, organizing the invitations, etc.) please solve it quickly
(Please do not give solution in image format thanku) Develope a 3 level work breakdwon structure (including level 1,2 and 3) the work break down structure is based on the following project. Improving Customer Service Response Time for a clothing company. additional informationa can be added to the work break down struture to create the different levels The motivation behind this project is to improve customer satisfaction by reducing response time for customer service inquiries. Currently, customers are waiting an average of 48 hours to receive a response to their inquiries, resulting in frustration and dissatisfaction. By implementing a new customer service ticketing system and training customer service agents on effective communication and problem-solving techniques, response time can be reduced to 24 hours or less.
Registration at Southern University has always been a time of emotions, commotions and lines. students must move among 4 stations to complete the process. last semester's registration is in fig. 9.20. 450 students moved from the paperwork station (A) to advising (B) and 550 students went directly from (A) to pick up class cards (C). preregistered graduate students went directly to pay (D). A to D is in a linear fashion and the distance from A to B, B to C and C to D is 30feet. a. calculate the movement cost or 'load x distance' of the layout b. provide an improved layout and provide its movement cost

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Practical Management Science

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

SEE MORE TEXTBOOKS