Answered: -Oil SG = 0.80 - Oil SG = 0.80 35 in 40…

Name: A water pipe is connected to a double-U manometer at a location where
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A water pipe is connected to a double-U manometer at a location where the local atmospheric pressure is 14.5 psia. Determine the absolute pressure at the center of the pipe. -Oil SG = 0.80- Oil SG = 0.8035 in40 inWaterpipe60 in15 in-MercurySG = 13.6

Engineering

Mechanical Engineering

-Oil SG = 0.80 - Oil SG = 0.80 35 in 40 in Water pipe 60 in 15 in -Mercury SG = 13.6

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter27: Commercial Ice Machines

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

A fluid at a certain temperature has a viscosity of 37.1 cP and a specific gravity of 0.8022. 49508.6 bbl of this fluid per day is transferred from a far-flung source 501.55 miles away using a 18.1 ID steel pipe. Given that the pump has an efficiency of 68.82%, what is the actual power requirement in kW Answer options: 269 8554 6949 1039 3236
fluid mechanics In order to prevent flooding in irrigation areas and to direct the water back to the river or waterbed, the flat cover system given below is preferred. The weight of the cover is 871 kg. The square section cover is hinged 1m above the center of the cover (a = 0.25 m) and b = 1.5 m. The cover has a vertical angle of 40 What should be the maximum water head (h) according to the instructions so that the cover does not open? (psu=1000kg/m3)
Convert 235.268 Kelvin to Rankine
How high must the pump centerline be located above the water level in an open tank that supplies water to the pump if it requires a minimum of 2.5m of NPSH? The barometer reading is 760mmHg, the pipe friction is 0.65m and the vapor pressure is 3.51kPa. 6.82m 5.48m 7.39m 4.99m
A fluid at a certain temperature has a viscosity of 36.52 cP and a specific gravity of 0.8565. 56324.4 bbl of this fluid per day is transferred from a far-flung source 525.44 miles away using a 23.02 ID steel pipe. Given that the pump has an efficiency of 80.37%, what is the actual power requirement in kW. i. 4105 ii. 3959 iii. 444 iv. 8059 v. 4268
Industrial Application of differential U tube manometer?
Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level of oil in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48 kPa absolute and its specific gravity is 0.82 Determine the NPSH in meters available.
Oil (specific gravity of 0.80 and a viscosity of 0.000042 lbf-sec/ft²) at a temperature of 80°F flows through two separate pipes 10 and 12 inches in diameter. If the mean velocity of flow in the 12-in pipe is 6 fps, the velocity of flow in the 10-in pipe will be,A. 21 fpsB. 21.5 fpsC. 22.0 fpsD. 22.5 fps
The present pumping rate of crude oil through the Alaska Pipeline with an ID of 39 in is 550,000 barrels per day (1 barrel is 42 U. S. gallons). For crude oil at 60ºC, take ρ = 860 kg/m3 and μ ≈ 0.004 kg/m·s. What would be the maximum rate if the flow were constrained to be laminar? Take π = 22/7. Answer is asking for maximum flow rate for barrels per day
A radial plain bearing has a diameter of 60 mm and a width of 60 mm. Journal rotation speed 600rpm; radial load acting on the bearing is 3.5 kN, the inlet temperature of the SAE 20 oil used is 30 C andSince r / c = 1000;a-) The increase in the temperature of the oil and its average temperature,b-) Minimum oil film thickness, angular position and eccentricity ratio,c-) Loss of power in the bed,d-) Side leaks and total oil flow,e-) Max. oil film pressure.
1) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 2) The EGL is always a distance V2/2g above the HGL. True or False
Define the Manometer breifly?