Someone can help me with this one please. 1. Oil (SG = 0.84) is flowing in a pipe under the conditions shown in Figure. Find the%3Dpressure at point 2.Point 1D, - 6 inP,- 65 psiQ = 2.08 efs10.70 ftQ = 2.08 cfsPoint 2Dz = 9 inPz =?4.00 ftReference datum

Find velocitiesUse continuity…

Answered: Oil (SG = 0.84) is flowing in a pipe…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Through the pipeline system in the figure calculate gauge and absulate presures at A and B
The elbow flow passage volume is 0.37 m3 between sections 1 and 2. The flow rate is 0.90 m3/s and the elbow inlet and outlet pressures are 200 kPa and 130 kPa. Consider the elbow weight is negligible. Calculate the horizontal and vertical anchoring forces to hold the elbow in place. my results were Frx = 132.8kPa Fry = 76.7kPa
What is the minimum diameter at section (1) in the pipe below to avoid cavitation at that location? Take D2 = 15 cm. Neglect friction head loss in the pipe.
A series of pipes with Q = 183 L/s was to be examined for head losses. If the roughness coefficient is 0.015, what is the total losses due to friction in meters? Use Manning's approach.
choose the correct answer Q1- A rock trapezoidal channel has bottom width (5)ft, water depth of (3) ft, side slope 2 vertical:1 horizontal, and manning coefficient n (0.044), the channel had slope of 0.0016. The discharge through the channel will be: * a) less than 100 ft3/sec b) (100.1 - 150 ) ft3/sec c) More than 150 ft3/sec e)none of all above
Calculate the hydraulic radius for the most economical rectangular section having depth y and width B. a) y/2 b) y c) 2y d) 3y
A 300mm radius sewer pipe is laid on a slope of 0.001 and has a roughness coefficient of 0.012. The depth of water is 3/4 of its diameter. Determine the following: a) hydraulic radius: ______meter b) discharge: _______ m3/s c) boundary shear stress: ________Pa d) cross-sectional area of flow: _________meter
A series of pipes with q=191 L/s was to be examined for head losses. If the roughness coefficient is 0.012, what is the maximum diameter (mm) of the pipe that could replace all three in that series? Use mannings approach. Pipe 1 = (diameter=0.47m) = (length=1742m) Pipe 2 = (diameter=0.29m) = (length=1862m) Pipe 3 = (diameter=0.27m) = (length=1236m)
A concrete pipe 750 mm in diameter is laid to a gradient of 1 in 200.The estimated value of Manning’s ?is 0.012m−1/3s.Calculate the discharge when:(a)the pipe is full;(b)the depth is 90% of maximum.Explain why the answer in (b) exceeds th
a. Compute the value of x b. Compute the area in the fill c. Compute thr area in cut
A channel has been designed to convey clear water to a fish hatchery. The design calls for aflow depth of 2.0 ft and a velocity of 2.0 ft/s. The channel is very wide so the side effects canbe neglected and the hydraulic radius taken as equal to the depth. It is to be constructed insand which has a median diameter ds = 0.915 mm (0.003 ft). For a flat bed in this materialthe Darcy-Weisbach friction factor is estimated to be f = 0.0185 and the required channelslope is S = 0.000145. The water temperature is 20°C and the kinematic viscosity υυ is = 1.08x 10-5 ft2/s. The specific gravity of the sand is 2.65. Clear water is admitted to the channeland it is imperative that no material be scoured from the bed since any sand in the hatcherywill result in instantaneous death of all the fish. Using Shields' diagram, determine if theexisting design is adequate to deliver clear water to the hatchery.
A rectangular channel 5.2 m wide by 1.4 m deep was laid to have a hydraulic slope of 0.001. Using n = 0.013. 1. What is its yield in m³/s? a. 16.63 b. 12.47 c. 19.12 d. 14.14 2. What savings in earth excavation could be realized by using most economical proportion? a. 0.85 cum b. 0.96 cum c. 1.05 cum d. 0.92 cum 3. What savings in lining per meter length could be realized by using most economical proportion? a. 0.8 m b. 0.944 m c. 1.13 m d. 1.04 m

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Oil (SG = 0.84) is flowing in a pipe under the conditions shown in Figure. Find the pressure at point 2.