Oil (SG = 0.90) flows downward through a vertical pipe contraction as shown in the figure If the mercury manometer reading, h, is 110 mm, determine the volume flowrate for frictionless flow 300mm 10.6m SG = 0,9 100mm SG = 13.6

Oil (SG = 0.90) flows downward through a vertical pipe contraction as shown in the figure If the mercury manometer reading, h, is 110 mm, determine the volume flowrate for frictionless flow 300mm 10.6m SG = 0,9 100mm SG = 13.6

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Related questions

Q: Determine the mass flow of the fluid if it has the velocity profile shown. The channel is 1.4 m…

A: There are many types of fluids like gas, liquid.it is having more functions like flexibility and…

Q: In the tank-pipe-tank system given in the figure, water flows from A to C in horizontal pipes. Darcy…

A: The free surface is the fluid surface subject to zero parallel shear stress, such as the interface…

Q: Water (P =1000 kg/m , p=1.59x108 kg /m.s) is flowing with the velocity of 0.25 m/s through a smooth…

A: i. Given data-

Q: Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the…

A: The answer is found to be Difference in level of two tank = 7.6 cm For explanation please refer the…

Q: Question 5 Water flows through a pipeline whose diameter varies from 20 cm to 10 cm in a length of…

Q: Driven by pressurized air in a tank, water flows through pipes (L1₁ = 40 m, L2 = 80 m, L3 = 20 m) of…

A: Given: A flow of water through pipe of length L1, L2 and L3 as shown in the figure Dynamic…

Q: Refer to the illustration below. A C B D Solve for the following: 1. Headloss in meters at Pipe A 2.…

Q: Three pipes of different lengths and diameters connected in series, discharges 160 liters per…

Q: Two adjacent rectangular tanks hold water as shown in the figure below. Considering the dimensions…

A: step1-

Q: An equilibrium liquid level condition is shown in the given figure. If additional 10 cm³ of water is…

Q: A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.55 mm. The nozzle shoots…

Q: determine the flow that comes out into the atmosphere in F, tabulate and plot the hydraulic gradient…

A: YA=11 m diameter of pipe 1,d1=30cm diameter of pipe 2,d2=18 cm Length of pipe 1, l1=80 m Length of…

Q: As shown in the figure, water flows through the horizontal branching pipe at a rate 280 L/s. Viscous…

A: If you want any specific question to be answered then please specify the question number or post…

Q: A hydraulic jack contains 2.0 litres of oil as the working fluid. The compressibility of the oil is…

A: Finding out absolute decrease in the volume of the oil.

Q: In the figure, a 50 mm pipeline leads downhill from a reservoir and discharges into air. If the loss…

Q: Example 2: A flow of water from a closed reservoir with interior pressure of 50 kPa to a pipe of…

Q: The pressure in the outlet pipe from the reservoir is 61.3 kPa abs and h =15 m. Because of the…

Q: A circular pipe of diameter 0.5 m carries the discharge of 50 liters/s. The head loss due to…

Q: 2. The diameter of a 3 meter pipe decreases from 450 mm to 150 mm. If the velocity is to decrease…

A: As per the question, it is given that the velocity should be decrease uniformly along the direction…

Q: The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be…

A: The given data is: Q=SN/100=0.21 m3/s λ=SN/1000=0.021 L=SN*100=2100 m

Q: 7. In the figure below, a 50 mm pipeline leads downhill from a reservoir and discharges into air. If…

A: Given data, Head loss hl = 44.2 m Elevation of A zA = 46 m Elevation of B zB = 0 m Diameter of pipe…

Q: Q1) Pressure gage B is to measure the pressure at point A in a water flow as shown in Figure Ql. If…

Q: Estimate the velocity at point (2) and discharge of oil that as a petroleum engineer want to release…

A: Estimate the velocity at point 2,V2=?

Q: Venturi meter as shown in Figure 2 has the cross-sectional area of 10 m² and 5 cm² at Point A and…

A: Given data in question Venturimeter Area 1 = 10m2 Area 2 = 5 cm2 Manometric column difference To…

Q: A 10 cm diameter sharp edged orifice (C=0.60) is located at the vertical side of a tank having a…

Q: Question: A duct of diameter 0.8 m carries gas (p = 1.3 kg/m³). At one point, the duct diameter…

Q: Consider Euler's equation for one-dimensional (horizontal) unsteady flow. In a 20 cm diameter…

Q: Estimate the velocity at point (2) and discharge of oil that as a petroleum engineer want to release…

A: Take point 2 as datumPressure at point 1, P1=100KPaPressure at point 2, P2=100KPaThe diameter of…

Q: In the figure shown, Zp = 4 m, length of pipe from the reservoir to the pump is 120 m, from the pump…

A: Given, f = 0.02 LAB = 120 m LCD = 1000 m

Q: Water (p =1000 kg/m³) is flowing through a tube with the constant surface area as shown in the…

A: Given:

Q: 10 cm diameter sharp edged orifice (C=0.60) is located at the vertical side of a tank having a…

Q: Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the…

A: Given data:- The given specific gravity is, SG=0.89

Q: A conical tank 4.5m on top and 4,7m tall has a 60mm diameter orifice at its bottom for its outlet.…

A: The given data is as follows: Top width of conical tank=4.5 mHeight of conical tank=4.7 mDiameter of…

Q: Two reservoirs are connected by two parallel pipes of equal length and of diameters 20 cm and 10 cm,…

A: To Determine the ratio of discharge in the larger diameter pipe to the discharge in the smaller…

Q: 2 m 5,5 m 1 D1 D2 8 m D3

Q: Two reservoirs are connected by two parallel pipes of equal length and of diameters 20 cm and 10 cm,…

A: Given- 2 Parallel pipes of equal lengthdiameter 20 cm & 10 cmwater level difference=5 m

Q: In a laboratory, a flow experiment is performed over a hydraulic structure. The measured values of…

Q: Pressure gage B is to measure the pressure at point A in a water flow. If the pressure at B 87 kPa,…

A: Apply pressure balance between X and X'.

Q: The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The…

Q: Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the…

Q: Example 2 What fraction of the mass flow rate m is diverted down the plate shown below? Neglect…

A: V1=30m/s m=5kg/s Theta=45° To find Force F

Q: Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of…

Q: 1. A rectangular channel has a contraction that smoothly changes the width to a minimum width of 1.5…

A: Note -We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: 7. As shown in the figure below, a pump lifts water through a 100-mm diameter ductile iron pipe…

Q: For the cross section of a culvert shown in figure, compute the moment of inertia about the…

A: Moment of Inertia of Triangular Part about X-axis : Ixx1 = bh336 + Ah'2 = (3 + 3)×6336 + (12×(3…

Q: Situation 2: An open cylinder vessel 1.2 m in diameter contains water at a depth of 3.75 m. 3) If it…

A: D=1.2m r=0.6m N1=85rpm NE=125rpm

Q: A water pipe having a 2.33 cm inside diameter carries water into the basement of a house at a speed…

Q: 3) An incompressible flow velocity field is given as 1 1 ệp + - êe [m/s] r r where r is in meters.…

Concept explainers

Principles of Seepage

In hydrology, when water flows down in a pore or crack of unsaturated soil due to gravity, the deep layer of soil is called seepage. It is the slow movement of water in the soil layer. Seepage is mainly found near hydraulic structures and is responsible for the stability of earthen-type hydraulic structures.

Question

Oil (SG = 0.90) flows downward through a vertical pipe contraction as shown in the figure If the mercury manometer reading , h, is 110 mm, determine the volume flowrate for
frictionless flow.
%3D
300mm
10.6m
SG = 0,9
3D
100mm
SG = 13.6

Select the correct response:
0041 m^3/s
0.043 m^3/s
O0044 m^3/s
0.042 m^3/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water flows in a wide channel at Fr=4.5 and y1 = 2.40 m. If the flow undergoes a hydraulic jump, calculate: y2
An underground conical tank, standing on its vertex, is being filled with water at the rate of 18pi ft3/min. If the tanks has a height of 30feet and a radius of 15feet, how fast is the water level rising when the water is 12 feet deep? a. 3/4 ft/min b. 1/4 ft/min c. 1/2 ft/min d. 1/3 ft/min
Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014 *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa
Points A and B are 5km apart along a new 60cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140KPa greater than at A. f=0.019. Determine the head loss in meters choices: 7.52 2.75 5.27 7.25 Determine the flow rate in lit/sec choices: 822.55 885.22 228.55 522.88
An open rectangular tank moves upward along a 30o-incline as shown in the figure. What is the slope (tanθ) of the lines of constant pressure inside the tank?
26. A trapezoidal canal with a base of 2.2 m has sides sloping at 45⁰ with the horizontal. If water flows at a depth of 1.1 m, find the hydraulic radius.0.71 m0.62 m0.77 m0.68 m
For a flow of 1500 liters of water per second through a circular channel of 2m diameter flowing half full. The value of Manning's constant is 0.015 for the rough concrete lining used. Compute the slope required for the flow in the channel.
Water flows through a vertical contraction (venturi) section. Piezometers are attached to the upstream pipe and minimum area section as shown. The velocity in the pipe is 3 m/s. The difference in elevation between the two water levels in the piezometers is 15 cm. What is the velocity at the minimum area?
Points A and B are 5 km apart along a new 60 cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140 KPa greater than at A. f= 0.019 Determine the head loss in meters. choices: 7.25, 5.27, 2.75, 7.52
An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
There is X=5m high water on the left side of a 3.5 m wide vertical cover sitting on the hinge shown in the figure. On the right, a water jet with a cross-sectional area of A=1100 cm2 hits the cover. a) Determine the horizontal hydrostatic pressure force acting on the cover and the vertical distance of the impact point to the hinge. b) What should be the Q flow rate of the water jet so that the lid remains vertical? (gravity forces will be neglected)