Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45 v18²/2g; B to C = 8.75 V18²/2g; C to D = 0.12 V18²/2g; D to E = 9 vg²/2g. The diameter from B to D is 18 inches and diameter from D to E is 8 inches. Determine the pressure at point C in psi. Į 5 FT A 50 FT E ZZ

Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45 v18²/2g; B to C = 8.75 V18²/2g; C to D = 0.12 V18²/2g; D to E = 9 vg²/2g. The diameter from B to D is 18 inches and diameter from D to E is 8 inches. Determine the pressure at point C in psi. Į 5 FT A 50 FT E ZZ

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Similar questions

SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
Please show all work including unit converstions and please make sure to show all units. For P1=10+(6), so P1=16 psi for P2=20+0, so P2=20 psi for D1= 1ft for D2=0.6ft for Q=5.4 cubic ft per second
Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the 1m x 5m gate shown in the figure. Pressure of air = 32 kPa Fluids: fluid a (s=3.93) fluid b (s=0.23) fluid c (s=1.19) h1= 0.7 m h2= 1.6 m h3= 3.7 m Round your answer to 3 decimal places.
A cylindrical tank having a diameter of 1.5 m and a height of 4 m is open at one end and close at the other end. It is placed below the water surface with its open end down. How deep below the water surface should the tank be placed if the depth of the water inside the tank is 1.8 m? a.6.0 cm b.5.90cm c.6.25cm d.7.0cm show your complete solution
The rectangular bin with an inclined gate AB is filled with oil to the depth shown. Determine the resultant force (kN) acting on the inclined side AB. Take density of oil - 900 kg/m^3 x=3.27 a=5.2 m b=30 degrees asap
In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
Determine the rate of flow of water through a pipe of diameter 10 cm and length 60 cm when one end of the pipe is connected to a tank and other end of the pipe is open to the atmosphere. The height of water in the tank from the centre of the pipe is 5 cm. Pipe is given as horizontal and value of f= 0.01. Consider minor losses.
Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the 2m x 5m gate shown in the figure. Pressure of air = 47 kPa Fluids: fluid a (s=3.8) fluid b (s=0.27) fluid c (s=1.68) h1= 0.9 m h2= 1.6 m h3= 3.9 m Round your answers in 3 decimal places
Based on the layout of the water supply system, as show in Figure 1, flow through the delivery pipe, Q = 2.50 cfs and diameter of the pipe, D = 2.65 inch with e = 0.015 inch. Ingore the minor pressure losses and use the following formulae to calculate the major pressure losses. The velocity of flow through the pipe and the friction factor, f, range are estimated to be nearly. Use g = 62.4 lb/ft^3 for water and use Moody's diagram. Water temperature is 20°C (68°F).
1.) convert a pressure head of 15 m of water to meters of oil (sp. gr. =0.75).2.) Convert a pressure head of 600 mm of mercury to meters of oil (sp. gr.= 0.75)
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend isinstalled in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the xand y for components of the thrust block to hold the pipe bend.
In figure 6, compute the pressure difference between m and n, in pounds per square inch, when: A. Fluid A is brine (sp gr 1.15), the gage fluid is oil (sp gr 0.92), and z = 47.77 in. B. Fluid A is water, the gage fluid is air, and z = 17.77 in.