On a VE - Ic graph:a) Draw a load line for a BJT transistor, and show the change of Q point with three different Isvalues. (ai< Ia2 < Is3) (Q1 , Q2, Q2). Explain the reason for the changes shortly.4)b) Draw the load line and show the change of Q point with three different Rc (Rci< Rc< Rc3)values (Is constant). Explain the reason for the changes shortly.

On a Vcz - Ic graph: a) Draw a load line for a BJT transistor, and show the change of Q point with three different Is values. (lar< lan < Ias) (Q1 , Q2, Q2). Explain the reason for the changes shortly. (= b) Draw the load line and show the change of Q point with three different Rc (Rcı< Rcz< Rc3) values (la constant). Explain the reason for the changes shortly.

On a Vcz - Ic graph: a) Draw a load line for a BJT transistor, and show the change of Q point with three different Is values. (lar< lan < Ias) (Q1 , Q2, Q2). Explain the reason for the changes shortly. (= b) Draw the load line and show the change of Q point with three different Rc (Rcı< Rcz< Rc3) values (la constant). Explain the reason for the changes shortly.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the transistor , IS = 4 × 10−16 μA,βF = 75, and βR = 4. (a) Label the collector, base,and emitter terminals of the transistor. (b) What isthe transistor type? (c) Label the emitter-base andcollector-base voltages, and label the normal direction for IE , IC, and IB. (d) Write the simplified formof the transport model equations that apply to thisparticular circuit configuration. Write an expressionfor IE /IB. Write an expression for IE /IC. (e) Findthe values of IE , IC, IB, VC B, and VE B.
In order to express the effect of the internal capacitors of BJT and the high frequency reception, the current gain expression depending on the frequency (Figure b) (hfe) is used in the case of collector emitter short circuit, voltage source connected at base end and emitter grounded (Figure la).. The catalog information of the 2N2222 transistor is given in Figure Ic. In the catalogue, when Ic=20 mA, it is seen as fT=250 MHz. a) Find the total capacitor effect for the case where gm> > wCμ. (Cpi) + (Cμ) = ?pF
IBQ, ICQ, VE, VCEQ, VC for a transistor with VBE = 0.6 and β = 50. Draw and label the DC load-line. From b, if transferred to the center of the load-line, determine new values of R1 and R2 and draw the final circuit.
Perform the following steps for the given circuits. 1)Examine the voltage value of VCE, if base-emiter junciton open-circuit?2) Examine the voltage value of VCE, if base-emiter junciton short-circuit?
Find Icsat, Ibsat, Vrc Vrb and determine the minimum lb value that will turn the transistor ON. Show the solution
Determine the VGS and VDS for the E-MOSFET circuit shown, with the parameters given on a datasheet I_D(ON)=500mA at V_GS=10V and V_GS(TH)=1V.
The transistor is Silicon with β = 100, a forward emitter-base voltage of 0.7 V and VECsat = 0.2 V. If V+ = 7 V, what is the value of ICsat in milliamperes, and find what value of VB will the transistor transition from saturation to active mode expressed in volts.
Give the significance of α in case of CB ,Explain the VI characteristics of Common base NPN transistor ? Draw all necessary diagrams.
Derive an expression for gm, in terms of K, Vto, VGSQ, and IDQ for an NMOS transistor operating in the triode region.
In the circuit given below, VDD = 20 V and IDSS = 20 mA and Vp = -1 V for both transistors (T1 and T2). For T1 and T2 transistors; a)-Calculate IDQ1 , VGSQ1 and VDSQ1 for T1 transistor with a mathematical (analytical) approach? b)-Calculate IDQ2 , VGSQ2 and VDSQ2 for T2 transistor with a mathematical (analytical) approach?
The operating environment temperature of the base polarized circuit varies between 25 ᶛC and 50 ᶛC.The β value of the transistor is 100 at 25 ᶛC and 150 at 50 ᶛC. Under these conditions, the transistor QAnalyze the behavior (Ic and VCE) in the operating zone and determine the effect of temperature on the circuit.EXPLAIN.
Draw the equations of the small signal model for BJT transistor