One input to an AM DSBFC modulator is an 800 kHz carrier with an amplitude of 40 vp. The second input is a 25 kHz modulating signal whose amplitude is 10 vp. Determine a. Upper and lower side frequencies b. Modulation coefficient and percent modulation c. Maximum and minimum positive peak amplitude of the envelope d. Draw the output frequency

One input to an AM DSBFC modulator is an 800 kHz carrier with an amplitude of 40 vp. The second input is a 25 kHz modulating signal whose amplitude is 10 vp. Determine a. Upper and lower side frequencies b. Modulation coefficient and percent modulation c. Maximum and minimum positive peak amplitude of the envelope d. Draw the output frequency

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2 (A) A frequency modulator is supplied with a carrier at frequency fc = 5 MHz and an audio tone signal of Am = 1 volt amplitude and frequency fm = 1 kHz. It produces a frequency deviation f of 10 kHz as the output of the frequency modulator. (3)(i) The FM waveform described above is passed through a frequency multiplier with a total multiplication factor of 18, that is, fout = 18*fc. After passing through the frequency multiplier, what is the frequency deviation f at the output?(ii) The output of the multiplier in part (a) is next input to a mixer stage with the LO oscillator frequency set at fLO = 55 MHz. Find the sum-frequency output fo of the mixer’s IF port and also find the magnitude of the frequency deviation f.
Given an AM DSBFC modulator with a carrier frequency of 100 kHz and maximum modulating signal of 5kHz. Find the following: Frequency limits for the upper and lower sidebands bandwidth upper and lower side frequencies when the modulating signal is a single frequency 3kHz tone sketch the output frequency spectrum
A phase modulator has a phase deviation constant Kp = 35 degrees/V. The carrier signal is ec = 8cos2(pi)(800k)t, volts and the modulating signal is em = 5sin2(pi)(2000)t, volts. a. What is the equation of the PM signal? b. What is the maximum phase deviation? c. What is the amount of deviation in the carrier phase angle at t = 160 micro-s?
There are stations having the maximum frequency deviation of 75 kHz, and the maximum audio frequency for the modulation is 15 kHz , find its deviation ratio. Determine the peak frequency deviation for a FM modulator with a deviation sensitivity of 12 kHz/V and a peak modulating signal of 9V. If the maximum frequency deviation of the carrier is 10 kHz and the maximum modulating frequency is 6.7 kHz, find the modulating index. A PM signal has a maximum allowed deviation of 22 kHz and an actual deviation of 5 kHz . What is its percent modulation?
Calculate the frequency deviation of an fm modulator with division sensitivity of 20 khz/V and operates at a carrier frequency of 99.1 Mhz omdulated by a 2.5 Vrms sinewave. What is the output frequency of the FM modulator?
For an AM, DSBFC modulator with a carrier frequency fc=801KHz and a maximum modulating signal frequency fm=9KHz, determine: a. Frequency limits for upper and lower side band b. Bandwidth c. Draw the output frequency spectrum c. d. State two advantages and two disadvantages of FM over AM.
What is Maximum Usable Frequency (MUF)? Derive the expression of MUF critical frequency (fcr) and skip distance assuming curve earth.
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
(i)Calculate the modulation indexes and sketch the output spectrums for both modulators.(ii) Analyze the modulation indexes and the bandwidth if the modulating signal frequencyfor both modulators changed to 1 kHz. Sketch the output spectrums.
Given an FM modulator with a deviation sensitivity K1= 3.7 kHz/V and a modulating signal vm = 5.2 sin(2π1,906t), determine the carrier swing in kHz For an FM modulator with an unmodulated carrier amplitude Vc= 14 V, a modulation index m = 1, and a load resistance RL = 8 ohms, determine the power (in watts) in the modulated carrier The percent modulation of the sound portion of a TV signal is 85%. The maximum frequency deviation for the sound portion of the TV signal as specified by the FCC is 25 kHz. Determine the carrier swing (in kHz) of the signal. For an FM modulator with 40-kHz frequency deviation and a modulating-signal frequency fm= 13 kHz, determine the bandwidth (in kHz) using Carson's rule. Given an FM modulator with a deviation sensitivity K1= 1.4 kHz/V and a modulating signal vm = 3.9 sin(2π1,948t), determine the peak frequency deviation in kHz. The percent modulation of the sound portion of a TV signal is 73%. The maximum frequency deviation for the sound portion of the…
For an FM modulator with a modulation index mf = 1, a modulating signalVm(t) = Vm sin(2π1000t) and unmodulated carrier Vc(t) = 10 sin(2π500kt),determinea) Number of sets of significant sidebandb) Their amplitudec) Then draw the frequency spectrum showing their relative amplitudesd) Determine the unmodulated carrier power for the FM modulator(assume a load resistance RL = 50 Ω)e) Determine the power in the modulated carrier and each side frequency,and sketch the power spectrum for the modulated wave.
Q1-The message signal m(t) into a FM modulator with the parameter kf=25 is shown in the following figure. a) Express the FM signal in time domain.b) Calculate and plot the frequency deviation in Hz.c) Calculate and plot the phase deviation in radians.