|(a) Draw the circuit diagram of 2-bits flash (simultaneous) method analog to digital converter and explain its work briefly? (b) A 555 timer connected as astable multivibrator with R1=15 k2, R2=100 k2, and Cl=0.02µf. Draw the circuit and determine the frequency and the duty cycle of the output square wave?

|(a) Draw the circuit diagram of 2-bits flash (simultaneous) method analog to digital converter and explain its work briefly? (b) A 555 timer connected as astable multivibrator with R1=15 k2, R2=100 k2, and Cl=0.02µf. Draw the circuit and determine the frequency and the duty cycle of the output square wave?

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter32: Standby Power Systems

Section: Chapter Questions

Problem 7R: Briefly explain the function of a transfer switch. _____

See similar textbooks

Similar questions

Which module of the microcontroller will definitely be used if an analog signal needs to be read in a circuit design to be made using the 89C52 microcontroller? a) Serial communication b) ADC c) Timer d) PWM e) I / O
In an R-2R type DAC circuit taken as logic 1 = 3 volts and logic () = 0 volts, if the output voltage is measured as l Vo l = 3.75 volts, design it by calculating the input logic value.
Please describe as simply as possible in detail, what a multiplexer circuit is, how it works. Please also provide as many examples as possible.
For the relaxation oscillator, what would be the effect on the oscillation frequency of doubling CE ? Of doubling R1 ?
It is required to generate a single pulse waveform (Vtrigg) of 5 Volts amplitude (peak-to peak) and 8 ms duration to trigger a defibrillator using the circuit below. Assuming R = 50 kΩ and of R2 = 5 kΩ calculate values of R1 and C. Also assume +/- VSAT = +/- 15 V.
[0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of Qunta levels? b) Calculate what is the quantization interval? c)V=3.2 volts rounded to what quantization level? Let's draw with Quantalama level chart
ANSWER ALL, I WILL UPVOTE IF CORRECT 16. the sum of the firing delay angle and the conducion angle is 260. true or false 17. it is a breakover type of device that turns on when the voltage across its terminals exceed a certain value. a. thyristor, b. BJT, c.Transistor, d. MOSFET 18. What is the maximum firing delay angle that can be achieved with a resistive gate control circuit? a. 180, b. variable, c.360, d.90 19. it is the minimum amount of gate current that will make the SCR conduct current given that the gate-cathode voltage is 0.7V a. saturation current, b. gate conduction current, c. gate turn-on current, d. holding current 20. When the anode is made positive with respect to the cathode of the SCR but there is no gate current. The SCR is operation in its? a. off region, b.forward blocking region, c. forward breakover region, d. reverse blocking region
. What value of filter capacitor is required to produce a 1% ripple factor for a full-wave rectifier havinga load resistance of 1.5 kΩ? Assume the rectifier produces a peak output of 18 V.
a) State the stages in the ADC (analog to digital converter) circuit and briefly explain each of these stages!b) Describe and briefly explain the working principle of flash ADC! What are the advantages and disadvantages!c) What is the resolution of the ADC? If the input voltage range is Vrange = 15 volts and the number of ADC bits is n = 8, determine the resolution of the ADC.
Write the working principle, design, circuit diagram and precaution of 555 timer as astable
Do it soon , now ( course” Digital Electronics Technique
Which circuit is normally used to perform serial-to-parallel and parallel-to-serial data conversion? Flash converter Shift register Successive-approximations converter Reference regulator