P12.1 A compound shaft consists of segment(1), which has a diameter of 1.25 in., andsegment (2), which has a diameter of 1.75 in.The shaft is subjected to a tensile axial load ofP=9 kips and torques T₁ = 7 kip in. and TB =28 kip in., which act in the directions shown inFigure P12.1. Determine the normal and shearstresses at (a) point H and (b) point K. For eachpoint, show the stresses on a stress element.xZTBTAP■HKA(1)B(2)

Step 1: Step 2: Step 3: Step 4:

Answered: P12.1 A compound shaft consists of…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the support reactions of the beam and determine the degree of indeterminacy in the figure. q:11
In the rigid frame as shown in FIGURE L, if the pulley weighs 2kN, find the following: 1. Reaction at C a. 8 kNb. 11 kNc. 10 kNd. 9 kN34. Reaction at Ba. 28.9 kNb. 27.28 kNc. 26 kNd. 24.7 kN3. Angle that the reaction at B makes with the horizontal. a. 32.71°b. 24.03°c. 31.98°d. 19.11°
a) The truss structure in Figure Q4 is supported at A and D with downward vertical load F1 acting at joint E and a downward vertical load F2 acting at joint C. The length of each truss member AB, BE, BC, CD and CF is 1.25 m. If F1 = 95 kN and F2 = 225 kN, determine the reaction force RA and RD at the supports A and D. Give your answers in kilonewtons (kN) to two decimal places. b) For the truss structure in Figure Q4, determine the forces FAE, FAB and FCF acting in members AE, AB & CF and clearly state if each member is in compression or in tension. Give your answers in kilonewtons (kN) to two decimal places. c) A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young’s Modulus, E, of 5.8 x 1011 N/m2, calculate: (i) the tie-rod’s extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (iii) the strain…
Calculate the vertical reaction at support B. When sketching FBD, assume the positive direction of all reactions in the positive direction of y axis. Enter your answer in kN to two decimal places.
Determine the magnitude of the force generated on element 3 if P = 14.8 kN and Q = 37.4 kN
Each of the three frame bars in the figure has a linear mass of 12 kg/m. Locate the position (?̅, ?̅) of the center of mass. Neglect the size of the pins and the thickness of the bars. Also calculate the reactions at the pinned fixed support at A and at the sliding support at E. What value would the reactions at A and E have if the bar BD were removed from the frame? Consider g = 9.81 m/s2
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
Determine the reactions and the moments in- duced in the members of the frame in Figure P11.27. Also determine the horizontal displacement of joint B. Given: I = 1500 in.4 and E = 3000 kips/in.2
A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. Where: Q=2 T=6
In the beam loaded as shown in the figure, 4. Find the reaction at the left support. a. 36 kN b. 25 kN c. 15 kN d. 35 kN 5. Find the absolute max shear a. 41 kN b. 71 kN c. 90 kN d. 105 kN 3. Find the location of maximum positive beam moment measured from point a. a. 4.437 m b. 5.437 m c. 1.732 m d. 2.273 m
The support B of the structure shown in Figure settled by 0.7 in. Determine all reactions using slope-deflection equations. Use E = 30,000 ksi and I = 240 in4.
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N If the plate had a weight of 332N (applied vertically downwards in the center of the plate), the module of F should be greater than 369.18N, so that it would still remain balanced in that position?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS