Part AThe 118-kg spool has a radius of gyration about its mass center of kG= 300 mm If the couple moment is applied to the spool and thecoefficient of kinetic friction between the spool and the ground is k =0.2, determine the angular acceleration of the spool, the accelerationof G and the tension in the cable. (Figure 1)Determine the angular acceleration of the spool.Express your answer to three significant figures and include the appropriate units.HÀValueUnitsSubmitRequest AnswerFigure< 1 of 1Part B0.4 mDetermine the acceleration of G.ВExpress your answer to three significant figures and include the appropriate units.0.6 mM = 450 N•mHA?ag =ValueUnitsSubmitRequest Answer

Given: Mass of Spool = 118Kg, kG= 300mm, μk = 0.2 Determine = Angular acceleration of the spool,…

The 118-kg spool has a radius of gyration about its mass center of kG = 300 mm If the couple moment is applied to the spool and the coefficient of kinetic friction between the spool and the ground is µ = 0.2, determine the angular acceleration of the spool, the acceleration of G and the tension in the cable. (Figure 1)

The 118-kg spool has a radius of gyration about its mass center of kG = 300 mm If the couple moment is applied to the spool and the coefficient of kinetic friction between the spool and the ground is µ = 0.2, determine the angular acceleration of the spool, the acceleration of G and the tension in the cable. (Figure 1)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The static andThe coefficient of kinetic friction is m =0.5 and m =0.4, respectively. h hThe crane is connected to the cable from point A as seen in Figure 3.it exerts a tensile force T(t) in the horizontal direction.Calculate the speed of the log at t=5 sec.
This is a Dynamics of Rigid Bodies subject. Thank you:) In the system of weights shown, the 400-N block has a tendency to move up the 36 ° incline due to the pull of the 600-N block. The coefficient of kinetic friction between A and the incline is 0.25. Assume the pulleys are weightless and frictionless. ( Note : The acceleration of Block A is twice the acceleration of Block B ) a. What is the acceleration of Block B?b. What is the tension in the cable?c. What is the velocity of Block A after 4 seconds?
A 500-kg elevator car shown is being hoisted by motor A using the pulley system shown. If the car is traveling with a constant speed, determine the force developed in the two cables. Neglect the mass of the cable and pulleys.
Blocks B has a mass of 20 kg and block C has a mass of 15 kg. The coefficient of static friction at the contacting surfaces is 0.2. Block A is suspended by arope that passes over a fixed cylinder and is attached to block B. The coefficient of static friction between the rope and the cylinder is 0.25. What is the largest mass block A can have without causing block B to slip the left?
A block with mass m=(24+12)kg is pulled by a horizontal force P applied at point B in Fig.3. The coefficient of kinetic friction between the surfaces is we = (5A+5)/(25+94). When the acceleration of the block is a=(1+9)/4 m/s?, determine the cable forces Tax and Top- 0=(A+8) A=1
The 4-lb pulley has a diameter of 1 ft and the axle has a diameter of 1 in. If the coefficient of kinetic friction between the axle and the pulley is μk = 0.20, determine the vertical force P is applied horizontally to the left on the rope required to lift the 20-lb block at constant velocity.
The man pulls on the rope at a constant rate of 0.5 m/s. Determine the angular velocity andangular acceleration of beam AB when Ɵ = 60°. The beam rotates about A. Neglect the thickness ofthe beam and the size of the pulley.
The 4-lb pulley has a diameter of 1 ft and the axle has a diameter of 1 in. If the coefficient of kinetic friction between the axle and the pulley is μk = 0.20, determine the vertical force P on the rope required to lift the 20-lb block at constant velocity.
We have a table that we seek to lift with a pulley. The table is uniform, with a weight of 73 Newtons, it is suspended by means of a cable 2.7 meters long, which is attached to the sides of the table and passes through a small pulley located at O. Determine the tension of the cable if: d1=0.43 m d2= 1.14 m
Determine the tension in cables BA and BC necessary to support the60-kg cylinder shown.
Two blocks A and B each weighing 250N are connected by a weightless flexible cable as shown. The coefficient of friction under block A and the plane is 0.2. Neglect the inertia of the pulley. Which of the following is the tension in the cable in Newtons?
In the system of weights shown, the 400-N block has a tendency to move up the 39°incline due to the pull of the 600-N block. The coefficient of kinetic friction between A and the incline is 0.25. Assume the pulleys are weightless and frictionless.( Note : The acceleration of Block A is twice the acceleration of Block B). a.What is the acceleration of Block B? b.What is the tension in the cable? c.What is the velocity of Block A after 4 seconds?