Part A The wind turbine has an efficioncy of 48 % in a wind that has a velocity of V= 3 m/s (Eigure 1) Suppose the air to be at a standard atmosphonc pressure with a tomparature of 20°C Determine the average velocity of the air passing through the bilades Express your answer to three significant figures and include the appropriate units. V= 247 Sum Previous Answers v Correct Figure 1 of 1 Part B Find the difforence betwoen the pressures just in front and just behind the blades Express your answer to three significant figures and include the appropriate units Ap = Value Units Submit BeauestAnswer

Part A The wind turbine has an efficioncy of 48 % in a wind that has a velocity of V= 3 m/s (Eigure 1) Suppose the air to be at a standard atmosphonc pressure with a tomparature of 20°C Determine the average velocity of the air passing through the bilades Express your answer to three significant figures and include the appropriate units. V= 247 Sum Previous Answers v Correct Figure 1 of 1 Part B Find the difforence betwoen the pressures just in front and just behind the blades Express your answer to three significant figures and include the appropriate units Ap = Value Units Submit BeauestAnswer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An industrial plant needs 1, 383,739 gallon ofwater per day which must be pumped from a laketo a height of 273 ft. through 1, 779 ft. of 11in. pipe with friction factor f=0.048.Consadering losses in the pump due to valvesand appurtenances equal to 5 times thevelocity head and the entrance loss equal to0.7 the velocity head, find the horsepowerrequired to deliver water needed. Choices:a.63.1 b.70.24 c .153.4 d. 183.45 subject- civil engineering- hydraulics
An industrial plant needs 1, 383,739 gallon ofwater per day which must be pumped from a laketo a height of 273 ft. through 1, 779 ft. of 11in. pipe with friction factor f=0.048.Consadering losses in the pump due to valvesand appurtenances equal to 5 times thevelocity head and the entrance loss equal to0.7 the velocity head, find the horsepowerrequired to deliver water needed. Choices: a.63.1 b.70.24 c .153.4 d. 183.45 subject- civil engineering- hydraulics Hint answers: letter B . 70.24, please show your solution
here are the answer, only need solutions 1.f = 11.46 MPa 2.Mcr= 88.90 kN-m 3.fconc= 17.14 MPa; fsteel= 318.20 MPa
Three pipes are connected in series. The first pipe has a diameter of 500 mm and a length of 600 m. The second pipe has a diameter of 400 mm and a length of 500 m. The third pipe has a diameter of 300 mm and a length of 200 m. Use f = 0.02 for all pipes. If Q=0.8 m^3/s, What is the equivalent diameter, in mm, of a single pipe having the same properties that could replace the three pipes? Round off to the neares whole number.
SHOW COMPLETE SOLUTION AND FINAL ANSWER INTO 3 DECIMAL PLACES 3. A large pipe called penstock in hydraulic work is 1.5 m in diameter. Here it is composedof wooden staves bound together by steel hoops each 300 mm2in cross sectional area, and is used to conduct water from a reservoir to a powerhouse. If the maximumtensilestress permitted in the hoops is 130 MPa, what is the maximum spacing between hoops under a head of water of 30m? Use density of water equal to 1000 kg/m3
I really n3ed this in 30 minutes pls hel mee i cant solve this. i give you upvote
3. Two concrete pipes are connected in seriesThe flow rate of water through the pipes is 0.14 m/s with a total friction loss of 14,10 m for both pipes. Each pipe has a length of 300 m. If one pipe has a diameter of 300 mm, what is the diameter of the other one? Neglect minor losses Use dot f = 0.021
Questions #1 Water flows at the rate of 0.16 L/s through a 200 mm diameter pipe. If its Viscosity is 1.15x10^6 m^2/s what is the type of flow? A. Subcritical B. Turbulent C. Supercritical D. Laminar Questions #2 From the steel pipe network shawn in Figure, the supply of water is 350 lit/sec. Calculate the following: a) Rate of flow of water in pipe 2 in Lit/s ( A. 151.7 , B. 198.3 C. 167.2 , D. 175.1) b) Rate of flow of water in pipe 4 in Lit/s ( A. 151.7 , B. 198.3 C. 175.1 , D. 198.3)
19. Situation 7 - Three pipes are connected in series. The first pipe has a diameter of 500 mm and a length of 600 m. The second pipe has a diameter of 400 mm and a length of 500 m. The third pipe has a diameter of 300 mm and a length of 200 m. Use f = 0.02 for all pipes. If Q=0.8 m^3/s, a. What is the equivalent diameter, in mm, of a single pipe having the same properties that could replace the three pipes? Round off to the neares whole number. b. What is the total head loss, in meters, from pipe 1 to pipe 3? Round off to three decimal places. c. What is the total head loss, in meters, in pipe 1? Round off to three decimal places.
2.Water (ρ = 1000kg / m3, μ = 10-3Pa.s) flows at a speed of 1.6m / s (Reynolds number Re = 0.8 105) in a pipe whose diameter is to be determined.
A simple turbomachine is constructed from a disk with twointernal ducts that exit tangentially through square holes, asin Fig. P3.156. Water at 20 ° C enters normal to the disk atthe center, as shown. The disk must drive, at 250 r/min, asmall device whose retarding torque is 1.5 N ? m. What isthe proper mass fl ow of water, in kg/s?
Hydrodynamics pumps (WRITE LEGIBLY) 2. A double suction, single-stage centrifugal pump is to be installed to deliver 250 gpm of water against a head of 225 ft. The pump is to be coupled to an electricmotor with an speed of 3450 rpm. Determine the type of impeller needed for this installation. a. type of impeller Answer : ____________________