Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. Originally the cable is unstretched. ▼ Part A AB = HÅ If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00484 mm/mm, determine the displacement of point B. Express your answer to three significant figures and include appropriate units. Value wwwww Units 600 mm ? B 800 mm

Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. Originally the cable is unstretched. ▼ Part A AB = HÅ If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00484 mm/mm, determine the displacement of point B. Express your answer to three significant figures and include appropriate units. Value wwwww Units 600 mm ? B 800 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Similar questions

Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00317 mm>mm, determine the displacement of point B. Originally the cable is unstretched.
A single strain gage, placed in the vertical plane on the outer surface and at an angle 60° to the axis of the pipe, gives a reading at point A of PA = -250(10-6). Determine the principal strains in the pipe at this point. The pipe has an outer diameter of 1 in. and an inner diameter of 0.6 in. and is made of C86100 bronze.
Material A has a modulus of elasticity between Materials B and C, where the value of Material B is the highest and Material D is the lowest. Materials A and B do not undergo plastic deformation with the same strain value. Material B has the same strength as Material C, but higher than Material A. The strength of Material A is the same as that of Material D. Materials C and D experience the same strain with considerable plastic deformation. a. Draw the stress strain curves of the 4 Materials in one axisb. If you are asked to select a material according to the following criteria (state and explain why): i. Highest toughness: ii. Highest stiffness Supreme power iv. Highest tenacity If an application requires a material with low stiffness and high ductility, which material will you choose? NEED IN RUSH THANKS
The nonuniform loading causes a normal strain in the shaft that can be expressed as Px = k sin ap L xb, where k is a constant. Determine the displacement of the center C and the average normal strain in the entire rod.
7) The strain of a component, which has a tensile modulus of 4 X 105 MPa, and subjected to a stress of 6000KPa, is a. 0.000015 b. 0.00015 c. 0.00003 d. 0.003
5 decimal places Determine the total strain (mm/mm) of a 2.64-m bar with a diameter of 21 mm subjected to a tensile force of 71 kN at a temperature increase of 49 C°. Consider the α=27.3 µm/mC° and E = 122 GPa.
The A-36 steel bar consists of two segments, one of a circular cross-section of radius r, and one of square cross-section. If the bar is subjected to the axial loading of P, determine the dimensions of the square segment so that the strain energy within the square segment is the same as in the circular segment.
The brake pads for a bicycle tire are made of rubber. If a frictional force of 50 N is applied to each side of the tires, determine the average shear strain in the rubber. Each pad has cross-sectional dimensions of 20 mm and 50 mm.Gr = 0.20 MPa.
Determine the strain if a rod is experiencing a stress of 70,000kPa with a modulus of elasticity of 175 GPa.a. 300 x 10−6b. 400 x 10−6c. 500 x 10−6d.. 600 x 10−6
The piece of plastic is originally rectangular. Determine the average normal strain that occurs along the diagonals AC and DB. Determine the shear strain at corners A and B if the plastic distorts as shown by the dashed lines.
An air-filled rubber ball has a diameter of 6 in. If the air pressure within the ball is increased until the diameter becomes 7 in., determine the average normal strain in the rubber.
Determine the vertical displacement of plate A due to shear deformations in the rubber. The cross-sectional dimensions of each shoe are 35mm X 25mm. G = 0.3 Mpa,