particular balanced three-phase system is supplying a (delta)-connected load with 10kW at a leading power factor of 0.7. If the phase voltage is 208V and the source operates at 50Hz answer the following: (a) compute the line current (b) compute the impedance Zp (c) draw a circuit diagram representing this system.

particular balanced three-phase system is supplying a (delta)-connected load with 10kW at a leading power factor of 0.7. If the phase voltage is 208V and the source operates at 50Hz answer the following: (a) compute the line current (b) compute the impedance Zp (c) draw a circuit diagram representing this system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.40P: A balanced three-phase 240-V source supplies a balanced three-phase Load. If the line current IA is...

See similar textbooks

Similar questions

Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at 0.9 power factor leading, are connected in parallel and supplied by a balanced three-phase Y-connected, 480-V source. (a) Determine the source current. (b) If the load neutrals are connected to the source neutral by a zero-ohm neutral wire through an ammeter, what will the ammeter read?
A three-phase line with an impedance of (0.2+j1.0)/ phase feeds three balanced three-phase loads connected in parallel. Load 1: Absorbs a total of 150 kW and 120 kvar. Load 2: Delta connected with an impedance of (150j48)/phase. Load 3: 120 kVA at 0.6 PF leading. If the line-to-neutral voltage at the load end of the line is 2000 v (rms), determine the magnitude of the line-to-line voltage at the source end of the line.
A balanced three-phase 240-V source supplies a balanced three-phase Load. If the line current IA is measured to be 15 A and is in phase with the line-to-line voltage, VBC, find the per-phase load impedance if the load is (a) Y-connected, (b) -conneeted.
A balanced, three-phase, positive sequence source, supplies power to a balanced delta-connected load. Additional information given for this system are as follows: Ic = 10.5 cis 98 degrees amps; and total reactive power is = 2623 vars, with 0.89 power factor lagging For the system, determine the magnitude of Vca in volts.
A three-phase, three-wire, 240 V ACB system supplies power to a wye-connected load with resistances and inductances of Za: 25 ohms, 15mH; Zb: 40 ohms, 10mH; Zc: 20 ohms, 18mH. Find the total average power delivered to the load if the line impedance is given by 2 ohms and 15mH.
In a balanced abc sequential three-phase star-star connected system, the total power on the line is 650W. If the VAN is 117/15 degrees Vrms, the load has a power factor of 0.88 (forward) and the line impedance is 1 + j2ohm, what is the load impedance?
A balanced delta-connected load has phase impedances of 4+j3 Ohms. It is connected to balanced transmission lines, with Vab = 1.5kV @ 15 degrees. a) What is the current through each of the load phases? b) What is the current through each of the transmission lines? c) Which ACSR cable should be used for these transmission lines to give a 20% current rating margin for this load?
A star-connected three phase power pack is connected to balanced star-connectedload of 2 + j3 Ω. The line current is 2∠0⁰ A. Assuming negligible impedance onthe cable, calculate:a) the phase and line voltages from the source. b) the real and reactive powers of the circuit.
A balanced, three-phase, positive sequence source, supplies power to a balanced delta-connected load. Additional information given for this system are as follows: Ia = 14.5 cis -1 degrees amps; and Zbc = 191 cis 75 degrees ohms. For the system, determine the magnitude of Vab in volts.
The following three parallel-connected three-phase loads are fed by a balanced three-phase source: Load 1: 250 kVA, 0.8 pf lagging Load 2: 300 kVA, 0.95 pf leading Load 3: 450 kVA, unity pf If the line voltage is 13.8 kV, calculate the line current and the power factor of the source. Assume that the line impedance is zero.
A Y-Y three-phase system has a source of 380 V and a load of impedance of 6+j5 Ohm/phase through a transmission line of 2+j 1 Ohm/phase.Plot this Y-Y three-phase system then calculate complex power supplied by the source.
A Y-Y three-phase system has a source of 380 V and a load of impedance of 6+j5 Ohm/phase through a transmission line of 2+j 1 Ohm/phase. Calculate complex power supplied by the source. C