Please answer completely with brief explanation in every step A 5-lb collar is connected to a spring with an unstretched length of Lo = 3ft. It slides along a curved pipe with a speed of v = 8.51 ft/s at the instant shown. (g = 32.17 ft/s) (a) Determine the total acceleration of the collar and the normal force from the pipe at this instant 2 ft 8.51 ft/s wwwˇˇˇˇˇˇˇˇ k = 10 lb/ft y = 8-0.5x²

Please answer completely with brief explanation in every step A 5-lb collar is connected to a spring with an unstretched length of Lo = 3ft. It slides along a curved pipe with a speed of v = 8.51 ft/s at the instant shown. (g = 32.17 ft/s) (a) Determine the total acceleration of the collar and the normal force from the pipe at this instant 2 ft 8.51 ft/s wwwˇˇˇˇˇˇˇˇ k = 10 lb/ft y = 8-0.5x²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider two blocks connected . BlockA has mass 2.00 kg, and block B has mass 5.00 kg. The table on whichB sits is frictionless, the cord connecting the blocks is light and flexible,and the pulley is light and frictionless. The horizontal force F S hasmagnitude F = 20.0 N, and block B moves to the left with an accelerationof 1.50 m/s2. What is the coefficient of kinetic friction that one block exerts on the other?
A block weighing 100Nis held on a 40 ̊incline by a bar attached to a 150N block on a horizontal plane. The bar, which is fastened by smooth pins at each end, is inclined 20 ̊above the horizontal. The angle of friction between each block and its plane is 18 ̊. Fin the horizontal force P applied to the 150N block which will cause to be on the point of moving (a) to the right; (b) to the left.
Calculate the vertical reaction at support A. Enter your answer in kN to two decimal places.
Figure 1.18 represents a beam in equilibrium with threeloads and two reactions. Select five different centers of moments and writethe equation of moments for each, showing that the sum of the clockwisemoments equals the sum of the counterclockwise moments.
Knowing that at the instant shown crank BC has a constant angular velocity of 45 rpm clockwise, determine the acceleration of Point A and Point D.
calculate the Moment in kip-foot at Point B if the given 30kip and 20kip loads from the figure are both replaced by 11kips and 14kips respectively. Express your answer in 2 decimal places. Include (-) negative sign if the moment is negative.
Given a 2-D force system with geometry as shown. Find the magnitude of the equivalent couple moment (Nm) acting at O if P = 507 N , Q = 382 N, and T = 451 N . Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of moment: use CW if clockwise , CCW if counterclockwise.
Find the force in member BD.A 40 lb ladder 12 ft long leans against the wall making an angle of 30° with the wall. When a 180 lb man reached a point 8 ft from the lower end, the ladder is about to slip. Calculate the coefficient of friction between the ladder and the floor. The coefficient of friction between the ladder and the wall is 0.20
Please solve the unknown forces using Three Moment Equation. Thank you. Wu = 23.2 kN/m L1 = 5m L2 = 6m
Hey Expert !Please answer this with explanation. Illustrate the shear and moment diagram Please Please solve in 25 minutes expert I will upvote Please solve early
The 42 foot long overhanging beam shown is supported by a pin at A and a roller at C. The beam supports a point load of 42 kips at point B. Determine the slope at pin A, deflection at point B, and the slope and deflection at point D. Modulus of Elasticity, E = 10,000ksi, Moment of Inertia, I = 2500in4. Let slope and deflection be functions of x, with x positive to the right.
Apply the asymmetric bending theory to the cantilever beam shown below to determine:I. Main moments and inertias.II. The angle of the neutral axis respect the horizontal.III. If ???? = (table) ???, work out the maximum F force that can be applied.3L = (7.5) mb = (57) cmh = (47) cmθ = (56) ° mpa 30