Answered: Please derive the C.O.P of the…

Please derive the C.O.P of the refrigerator as a function of temperature using the temperature-entropy diagram. Assume ideal conditions. Thank you very much

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 12RQ: Refrigerators currently being manufactured in the United States are using______as their refrigerant.

See similar textbooks

Related questions

Q: Some ECOR1048 students are curious about expanding their knowledgebase and conduct an experiment. Th...

Q: For the mechanism in the image below, the end A of the bar is moving downward along the slotted guid...

A: Given that, VA=2 m/sec,r=0.5 m,θ=49°,x=y2-r2 From the triangle given in the figure, sinθ=ry .......

Q: Q5. According to the manufacturer, a Porsche Spyder reaches 0-100 kmph in 3 seconds. A person starts...

Q: Determine the resultant internal loadings on the cross section at point D. 1 m 2 m 1.25 kN/m DEB 15 ...

Q: A horizontal pipe carries oil with a specific gravity of 0.83. If two pressure gauges along the pipe...

Q: Iron exhibits an allotropic behavior change of solid state structure in such a way that when it is h...

Q: What is the center type of this valve?

A: See the answer in the next page.

Q: At steady state, a device receives a stream of saturated water vapor at 210°C and discharge a conden...

A: Given Data The vapor temperature is:T1=210°C The steam temperature is:T2=20°C The pressure of steam...

Q: 3 The velocity of a particle which moves along the x axis is given by v = 2 – 4t + 5 tz, where t is ...

Q: 13-15. A freight elevator, including its load, has a mass of 500 kg. It is prevented from rotating b...

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat ske...

Q: 6. A 130 cc block has a piece of lead tied to it. Suppose that the SG of lead is 11.13 and SG of the...

Q: 8. As shown in the figure below, oil is inside the hydraulic press with SG=0.82. What force F is req...

A: GIVEN DATA- A HYDRAULIC PRESS GIVEN WE HAVE TO FIND FORCE F

Q: 2. A fluid (s=0.95) flows through a 77 mm diameter pipe at a velocity of 6 m/sec. Compute the mass f...

A: Given data: SG=0.95d=77 mmv=6 m/s Need to determine the mass flow rate of the fluid.

Q: motor required?

A: To find power required

Q: A polytropic process is carried out from an initial pressure of 110 kPa and volume of 5 m3 to a fina...

A: From the given data, Initial pressure = P1 = 110 kPa Initial volume = V1 = 5 m3 Final volume = V2 = ...

Q: For the following mechanism, if velocities vc = 3.7 m/s, and va = 4.0, determine the magnitude of th...

A: Given: V_A = 4.0 m/s V_C = 3.7 m/s To find: Angular velocity of AC = ?

Q: A U tube manometer uses glycerin as the measuring fluid. What will be the differential pressure if t...

A: Given data, h = 103 in = 2.6162 m ( h = difference of glycerin levels ) Density of glycerine = ...

Q: 3.) The system in the figure below is at 20 °C. If the pressure at point A is 2900 lb/ft², determine...

Q: The sugar content of the syrup in canned peaches is normally distributed, and the variance is though...

Q: 5/146 The revolving crank ED and connecting link CD cause the rigid frame ABO to oscillate about O. ...

A: Given that, Angular velocity, ω=0.4 rad/sec,Angular acceleration, α=0.06 rad/sec2

Q: In the position shown crank AB has a constant angular velocity of 20 rad/s CCW. Determine the veloci...

Q: bb) Hot air at 60 °C leaving the furnace of a house enters a 12 m long section of a sheet metal duct...

Q: The throat diameter of a perfect venturi meter is 1.99 inches and is placed horizontally in a pipe w...

Q: (42) The two uniform bars shown in Fig. (25) are of equal length and equal mass. Determine the equat...

Q: Determine the address indices shown in the following cubic unit B A 1 1 +y 1 1 22 +x 2/3 DI 1/2 -/3

Q: 4. The vertical plate ABED is pinned to rod OA at A and supported by a roller at E which slides in a...

A: Given DataVE=0.7m/s

Q: The ordinary household refrigerator is a good example of the application of this cycle. Eaporater Fr...

Q: Determine the head developed by a multi-stage pump delivering 50 L/s when running at 1450 rpm if the...

Q: A tank contains 21 kg of dry air and 0.3 kg of water vapour at 24°C and 100 kPa total pressure. Dete...

Q: The force R is the resultant of the forces F1, F2 and F3 acting on the rectangular plate. See figure...

Q: A tank is sealed tight and has a water level that is 11.3 m above the ground. The pressure above the...

Q: At vertical fall, water creates pressure in A. Having 12.62 psi in B, determine pressure in A in kPa...

Q: The rate of flow of water through a horizontal pipe is 200+last two digits of your id lit/s. The are...

A: according to the given details provided.

Q: 600 N/m The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. De...

Q: A1.8-m-diameter spherical tank of negligible thickness contains iced water at 0°C. Air at 25°C flows...

Q: A pressure vessel has 0.34 m of net furnace area supported by SA-36 stay bolts, spaced by 0.124m. Th...

A: Given DataP=1.375MPaA=0.34m2Spaced=0.124m

Q: A load of 25 KN is to be supported by three 20KN equidistant vertical rods as shown. At first, all t...

Q: Consider the S 510 x 98.2 beam shown below where Oall = 160 MPa. Complete the following: a) Calculat...

Q: In a circular tube of diameter 100 mm and length 13 m with laminar low, the friction factor is estim...

A: Diameter of tube, d=100 mm=0.1 mTube length, L=13 mType of flow, = Laminar flowThe friction factor, ...

Q: Which of the following is/are not true? i. Specific gravity is sometimes termed as relative density....

A: It is required to choose correct answer

Q: 4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the...

A: Given data as per the question Load =25 KN Additional load = 20 KN Young modulus of steel = 205 Gpa ...

Q: In performing his favorite workout routine, Jason throws a ball with an initial velocity of 12.3 m/s...

Q: Determine the reaction at the support B in N for equilibrium of the beam if w1-133 N/m. w2 - 264 N/m...

A: Apply Equilibrium Conditions for above FBD

Q: - As illustrated in the diagram, a cantilever beam supports a uniform distributed load of 60 kN/m. D...

Q: 4. A sliding gate of height 14mand width 28lies in vertical plane that weighs 25AN. Determine the ve...

A: Given: Height of the gate→h=1.4 m Width of the gate→b=2.8 m And wieght of the plate→W=25 KN because ...

Q: I need to calculate the tensile stiffness along the fibre which have a length of 250um below are t...

A: Given: Matrix Stiffness, Em = 6 GPaMatrix Strength = 50 MPaFibre Volume Fraction, vf = 0.41Fibre Sti...

Q: A manometer with two tubes are connected to the roof of a car. The first tube points to the front of...

A: Given DataS.G=0.64s=2.7 inces

Q: 6m $6,ster 1.025 seas A semicircular 4m gate

Q: The :Q4 = 26 in.; CBE = 27 in. represents a crank and rocker m used in a certain type of wool- machi...

A: To given thatQ2B=5in Q2Q4=26inBC=15in CBE=27inQ4C=21in ...

Question

Please derive the C.O.P of the refrigerator as a function of temperature using the temperature-entropy diagram. Assume ideal conditions. Thank you very much

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider natural gas furnace, electric resistance heat pump systems. For a specified heating load, which one of these three systems will do the job with least irreversibility? Explain.
What is the COP of the Carnot refrigerator if the COP of the Carnot heat pump is 2.3 where two cycles are operation between identical reservoirs?
Dual cycle's four processess in P-V and t-s DIAGRAM, explanation, equations, efficiency derivation, advantages and disadvantages
Consider a household refrigerator that uses HFC-134a as the refrigerant, operating between the pressures of 1.0 bar and 10 bars. Determine the enthalpy at each ofthe points 1, 2, 3, and 4, and calculate the coefficient of performance. Compare to the COP of a Carnot refrigerator operating between the same extreme temperatures. Does this temperature range seem reasonable for a household refrigerator? Explain briefly.
Steam power plant shown in figure isoperating at steady state with water as the workingfluid. The mass flow rate of the water circulatingthrough the components is 50 kg/s. Determine: d) isentropic pump efficiencye) mass flow rate of the cooling water, in kg/s.f) rates of entropy production, each in kW/K, forthe turbine and steam generator.Include all the relevant governing equations andreferences to the tables you use. Be organize
Fast ,Do not hold. Two heat engines receive heat from a source at temperature of 550◦C. Heat engine "A" receives 200 kJ of heat and rejects the waste heat to a sink at 180◦C. Heat engine "B" receives 180 kJ of heat and rejects the waste heat to a sink at 120◦C.(a) Caclualte the generated entropy, Sgen, in both processes.(b) Based on your answer in part (a), identify the heat transfer that is more irreversible.
Define the no refrigerator can have a higher COP than a reversible refrigerator operating between the same temperature limits.
A flash chamber has R-134A entering with a quality of 0.25 at a pressure of 5 bar. The saturated liquid from the flash chamber goes through a throttling value, an evaporator, and a compressor where it is compressed to 5 bar and 40°C. The saturated vapor from the flash chamber recombines with the remaining refrigerant in an open heat exchanger at a pressure of 5 bar. What are the enthalpy and temperature of the refrigerant exiting the heat exchanger?
2000 kg cast iron hoisin at 350 degree Celsius is quenched in 4000 kg of water at 15 degree Celsius. Find the amount of heat transferred to the water bath, entropy change for water and cast iron, use the entropy generation to prove that the entire system does not violate the second law of thermodynamics. Water specific heat of 4.18kj/kg.k, cast iron specific heat of 0.42kj/kg.k
a refrigerator operates at steady state using 500 W of electric power with a COP of 2.5 . what is the net effect of the kitchen air?
In a household refrigerator, the condenser is vertically mounted at the outer backof the unit, the freezer (evaporator) on the topmost compartment, and thevegetable compartment at the very bottom. Explain why?
Refriegerant ammonia enters the compressor of a refriegerant as a superheated vapor at 0.14 MPa, -20 °C at a rate of 0.04 kg/s, and leaves at 0.8 MPa, 50 °C. The refriegerant is cooled in the condenser to 0.75 MPa and is throttled to 0.14 MPa. Disregarding any heat transfer and pressure drops in the connecting lines between components, determine:a) the rate of heat removal from the refriegerated space in kWb) the power input to the compressor in KWc) the COP pf the cycle