Please give a neat and understandable configuration. Thanks. Assume there are 4 voice channels, each occupying a bandwidth of 40 kHz. These 4 voice channels need to be combined into a link with a minimum bandwidth of 175 kHz, from 131kHz to 306 kHz. There are guard bands of 5 kHz between the channels to prevent interference. Show the configuration using the frequency domain

Please give a neat and understandable configuration. Thanks. Assume there are 4 voice channels, each occupying a bandwidth of 40 kHz. These 4 voice channels need to be combined into a link with a minimum bandwidth of 175 kHz, from 131kHz to 306 kHz. There are guard bands of 5 kHz between the channels to prevent interference. Show the configuration using the frequency domain

Management Of Information Security

6th Edition

ISBN:9781337405713

Author:WHITMAN, Michael.

Publisher:WHITMAN, Michael.

Chapter6: Risk Management: Assessing Risk

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

Network latency issues are often caused by SELinux or AppArmor restrictions. True or False?
please answer with proper explanation and step by step solution. Question: Error Control involves taking one of three actions: (1) Toss the frame/packet; (2) asking to resend he frame/packet that was in error; (3) correct the error without retransmission. Discuss the advantages/disadvantages for each of these scenarios. What is the single greatest advantage of having a checksum for only the IP header? Why is cyclic redundancy checksum (CRC) implemented for Ethernet and for wireless frames as an error control technique?
Why are there much greater packet losses at the beginning of a transmission when using the TCP Tahoe network configuration as opposed to when using the usual timeout (packet losses when using the regular timeout may be significantly higher at the beginning of a transmission)? I was wondering if you could provide me an example of a link that, beginning at time t0, is able to transmit successfully, has a presumable capacity, and has a starting CW value. ..
Perform a Bridge Configuration in Cisco Packet Tracer Connecting two LANs?
Consider the following IP address and subnet mask.131.0.10.11255.255.128.0 What is the Network ID for the above IP address? How many bit have been borrowed in this case? What is the broadcast ID for the Network ID you found earlier?
There is the potential for MAC addresses to be shared across several network interfaces. Why is it that you are choosing not to do it? When using several network interfaces, does this increase the likelihood of IP address conflicts? Is there a justification for this action?
In a GSM network, there are eight intervals that are as separate as night and day in a "TDMA frame". The chat time on a GSM network is not just a drop in the bucket. How many bits are packed into a TDMA frame, including both the nitty-gritty data and the bossy control?
In the topology, Laptop 1 (Please assign an IP address from your design) sends a packet to Laptop 3 (Please assign an IP address from your design). Show the contents of the packets and frames at the network and data link layer respectively for each hop interface. You may assign any MAC address contains 12 Haxa Decimal Character at each hop interfaces between source and destination. A Sample MAC address is given in the topology.
Under what circumstances might you choose an ad hoc wireless network and how do wireless networks control media access? Do you use an ad hoc wireless network either at work or at home? Please explain what led to that decision. How does static routing work, and what are the advantages and disadvantages of this process? What is the difference between Address Resolution Protocol (ARP) and Reverse Address Resolution Protocol (RARP)? Do you believe our society will be at a point where we are without wireless networking? What are the pros and cons? What lessons did you learn from the Module 3 lab?
You are examining a host with an IP address of 52.93.24.42/20 and want to determine the broadcast address for the subnet. 52.93.31.255 is the correct broadcast address for the subnet but explain why?
32222 data bytes are transferred from client to server over a TCP connection over a point-to- point line using Ethernet frames (total overhead = 26 bytes, assume no interframe gap.). The connection parameters are the following: MSS=1280 for both ends, initial sequence number for client is 543 and for server is 99992. The client initiates the disconnection right after finishing data transmission by sending the FIN flag and server replies by sending the FIN flag. Assume the window size is 20000 bytes on both sides and no options in IP and TCP headers. Also assume one ACK segment is sent for each data segment. (a) Show a diagram of a data frame and a control frame (ACK, SYN, etc). Show how many bytes in each field: Eth header, payload, trailer. Assume padding is used for Ethernet frames with a data length less than 46 bytes. the answers are data: 1306 bytes, control: 72 bytes. I need clear explanation of every field in ethernet frames and how did you know the size of each field?
32222 data bytes are transferred from client to server over a TCP connection over a point-to- point line using Ethernet frames (total overhead = 26 bytes, assume no interframe gap.). The connection parameters are the following: MSS=1280 for both ends, initial sequence number for client is 543 and for server is 99992. The client initiates the disconnection right after finishing data transmission by sending the FIN flag and server replies by sending the FIN flag. Assume the window size is 20000 bytes on both sides and no options in IP and TCP headers. Also assume one ACK segment is sent for each data segment. (a) Show a diagram of a data frame and a control frame (ACK, SYN, etc). Show how many bytes in each field: Eth header, payload, trailer. Assume padding is used for Ethernet frames with a data length less than 46 bytes. the answers are data: 1306 bytes, control: 72 bytes. Explain the answers