Please solve the below question and give the solution in m3/day/m2 only not in feets. please solve it as early as possible. Determine the ground water infiltration rate for a new four-lane pavement with the following characteristics: Lane width = 3.6m Shoulder width = 3m Length of contributing transverse cracks (Wc) = 12m Rate of infiltration (Kp) = 0.015 m3/day/m2 Spacing of transverse cracks = 12m

Please solve the below question and give the solution in m3/day/m2 only not in feets. please solve it as early as possible. Determine the ground water infiltration rate for a new four-lane pavement with the following characteristics: Lane width = 3.6m Shoulder width = 3m Length of contributing transverse cracks (Wc) = 12m Rate of infiltration (Kp) = 0.015 m3/day/m2 Spacing of transverse cracks = 12m

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter19: Design Of Flexible Highway Pavements

Section: Chapter Questions

Problem 18P

See similar textbooks

Similar questions

Given a concrete pavement with a thickness of 8 in. (203 mm), a kvalue of 100 pei (37.1 MN/m³) doweled joints, and no concrete shoulders, determine the allowable repetitions under a 54-kip (240-kN) tridem-axle load based on erosion enteria. The Question is related to Highway and transportation Engineering.
13. Refer to Figure 3.1 attached. In the flexible pavement design example illustrated in the figure, what would be the required structural number if designing for W18=2,000,000 instead?a. 1.5b. 4.3c. 6.1d. 7.3
What are the ASHTO design considerations for flexible pavements? What are the ASHTO design considerations for rigid pavements? Give descriptions in each.
A 10-meter wide concrete road pavement 600 meters long is desired to be constructed over a well-compacted gravel road, together with the necessary concrete curbs and gutters on both sides. In order to put the subgrade on an even level grade, a 550 cu.m. Of sand filling is necessary, over which the, 35-cm concrete pavement will be placed. How much will the project cost, allowing for 15% contingency, and assuming the following data: (a) Sandfill, including rolling and watering- P15.00 per cu.m (b) Concrete curb and gutter (labor and materials) - P12.00per linear meter. (c) Concrete pavement, 25 cm thick (labor and materials), including curing- P25.00 per sqm.
Assuming the bedrock is impermeable, determine the time it took the clay layer to reach 90% consolidation after sand fill placement and after sand fill removal. Assume cv = 8 e-6 ft^2/s.
Propose the basic concept of penetration test of bitumen
Calculate for the liquid pressure experienced using the equation: P=pgh solve in GRESAJ format height = 7.10 feet Flood density is generally assumed to be 62.4 g/mL regardless of the amount of debris. Cement can withstand a pressure of ≈ 28728.2 Pa.
A slab has a dimension of 0.10 meter thick, 6 meters wide and 10 meters long, Considering the slab to be resting on the ground fill, determine the volume of gravel required using Class C mixture. choices: 6 3 7
DESIGN OF A RIGID PAVEMENT1. Give a summary of rigid pavement design procedure by AASHTO method (1993), anddescribe the variables used in the method.2. Explain the CBR test; how to conduct the test and its purposes. Where are the usages oftest results in practical applications? Explain its advantages and disadvantages.3. Determine the thickness of a rigid pavement (thickness of concrete slab) by using thedata provided below:DATA PROVIDED:1. Cumulative 18kips ESAL = 5.000.0002. Overall standard deviation = 0.33. Reliability = 95%4. Design serviceability loose =1.75. Drainage coefficient = 16. Load transfer coefficient = 3.27. Mean concrete modulus of rupture = 650 psi8. Elastic modulus of the concrete to be used = 5.000.000psi9. Results of CBR test on subgrade material in the laboratory (Table 1):10. Standard force-penetration data.
What are the ASHTO design considerations for flexible pavements? What are the ASHTO design considerations for rigid pavements? Give a brief description in each considerations.
In a construction site, the contractor found out that average value of the test samples showed that water content is at 14.6%, specific gravity is 2.81 and the unit weight is 18.2 kN/m³ for the base course of the road. If the standard specifications require a void ratio of less than or equal to 0.80, has the contractor complied with the specifications?
Q1.(b) Does the penetration test value has any impact on other bitumen tests values? If yes , explain.