Plot the magnitude of the resultant R of the three forces as a function of 0 for 0≤0≤360°. After you have the plot, determine the value of which makes the magnitude R of the resultant of the three loads (a) a maximum and (b) a minimum. Record the magnitude of the resultant in each case. Use values of p = 79° y = 29°, F₁-69 N, F₂=118 N, F3 = 90 N. F₂ Answers: (a) maximum R= i N when 9- i (b) minimum R = i N when 0- i

Plot the magnitude of the resultant R of the three forces as a function of 0 for 0≤0≤360°. After you have the plot, determine the value of which makes the magnitude R of the resultant of the three loads (a) a maximum and (b) a minimum. Record the magnitude of the resultant in each case. Use values of p = 79° y = 29°, F₁-69 N, F₂=118 N, F3 = 90 N. F₂ Answers: (a) maximum R= i N when 9- i (b) minimum R = i N when 0- i

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There is a cylinder X weighing 735.75 Newtons that is held against a smooth incline and is being supported by a weightelss rod Y at 20°. Calculate all the forces that is acting on cylinder X. Solve using equilibrium of concurrent force system. Draw fbd please thank you.
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
For the distributed load shown below, determine the equivalent force’s magnitude (in kN) and location, measured from point O (in metres). Let a = 0.312 kN/m^3 , b = 1.08 kN/m^2 , and L = 3.46 mm .
A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determinethe safe compressive load. (Figure below)adding a cover plate on the figure of the same size at the bottom, compute the centroidal moment of inertia about x and y axes
Determine the load on the horizontal projection ( kips/ft) for the rafter in the figure shown if the load along the slope is one kip/ft of sloped length.
A block weighing 100 kN is pushed by a horizontal force of 100 kN along a smooth horizontal plane from A to B,10 m distant. The velocity of the block at A is 10m/s. The block is released at B and passes through an upward circular arcBC (tangent to B) of radius 10m and central angle 45 degrees and along an inclined plane CD tangent to the arc at C.Required: Sketch the given conditions and draw the necessary FBDs. Then determine the following:a. the velocity of the block at B.b. the velocity of the block at C.c. the distance along CD that the block will move before it comes to rest.
If FB = 700 N, and FC = 560 N, determine themagnitude and coordinate direction angles of the resultantforce acting on the flag pole.
calculate the Axial Force in kips on member BC if the given 30kip and 20kip loads from the figure are both replaced by 89kips and 31kips respectively. Express your answer in 2 decimal places. Include (-) negative sign if the axial force is compression.
In Step 6, sum of vertical forces, looks like you forgot an 8kip downward load
A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area. The correct answer is 2.84. Show solution.
Determine the magnitude(lb) of the vertical component of force at point C if P = 137 lb, x = 14.7 in, y = 8.3 in, and z = 7.5 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction: use U if upward and D if downward.
Using virtual work method, find: (a) the real internal force F in member BF in kN (b) real internal force F in member GH in kN (c) virtual internal force Fv in member HG due to a one unit horizontal load applied at joint G (d) virtual internal force Fv in member CD due to a one unit horizontal load applied at joint G (e) horizontal displacement at joint G due to the applied loads in mm. Given: a=25kN b=22kN c=4km