Pole-Zero Plot (4 Punkte) Sie haben die folgende Antwort gegeben: Below you can find two filters. Calculate the poles of the cascaded filter (connected in series) of H₁ and H₂ and mark their positions in the pole-zero plots below. For the first filter, you have the transfer function and the pole-zero plot -4x²-3x H₁(x) = -2x²+2x-1 This is the pole-zero plot for H₁: 1.5 1.0 0.5- 0.0 -0.5 -1.0 -1.5+ -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 Re For the second filter, you have only the transfer function: H₂(2) 10z²-0.5x+0.75 x²-0.75% Mark all areas in the pole-zero plot below where you expect the poles of the cascaded filter of H₁and H₂.

Pole-Zero Plot (4 Punkte) Sie haben die folgende Antwort gegeben: Below you can find two filters. Calculate the poles of the cascaded filter (connected in series) of H₁ and H₂ and mark their positions in the pole-zero plots below. For the first filter, you have the transfer function and the pole-zero plot -4x²-3x H₁(x) = -2x²+2x-1 This is the pole-zero plot for H₁: 1.5 1.0 0.5- 0.0 -0.5 -1.0 -1.5+ -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 Re For the second filter, you have only the transfer function: H₂(2) 10z²-0.5x+0.75 x²-0.75% Mark all areas in the pole-zero plot below where you expect the poles of the cascaded filter of H₁and H₂.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the circuit of a low pass RL filter and find the transfer function. Cutwith a frequency of 70 HzDesign a low pass RL filter. The amplitude-frequency-curve of this filter you designed.Draw in accordance with the calculated values.
Answer the following wuth illustration and solutions. 1.) A second-order band pass filter is to be constructed using RC components that will only allow a range of frequencies to pass above 500Hz and below 1.5kHz. Assuming that both the resistor have values of 1kohms, calculate the values of the two capacitors required. Find also the center frequency of the two frequencies. This is the example/guide that might help.
1. Design an active bandpass filter using a cascade connection by using a 6 μF capacitor togive a bandwidth of 800 Hz, a center frequency of 250 Hz, and a passband gain 2.Determine the following: ωc1 and ωc2 (lower and upper cutoff frequencies in rad/s), RLand RH, and Ri and Rf. Draw and label the designed filter.
Design a filter that will pass the two signals x1(t) = 3 cos(2000t + Ti/4) and x2(t) = 2 sin(4000t) and will block the two disturbance signals: xa1(t) = sin(100t) and xa2(t) = 2 cos(10,000t + t/3). 1. By hand show all calculations, find the system transfer function, and draw the circuit diagram 2. Use MATLAB to simulate the filter. Draw the combination of the four input signals. Use the transfer function found in part 1, and find the filter output. Then, draw the Bode diagram
For a High pass filter with a series resistor R1 = 24 kohms and inductor L = 16 mH with a load resistor R2 = 15 kohms, find the: a. transfer function [H(s)] without the load R2 b. transfer function [H(s)] with the load R2 c. what is the cutoff frequency without the load R2 d. what is the cutoff frequency wit the load R2
You need an active lowpass filter that has a cutoff frequency of 500 Hz. If the stopband is defined as being -20dB from the passband, and you need this value to be reached at 600 Hz, please show three different filter options, and comment on their frequency and time domain characteristics. ..
Design a second order lowpass filter using Tow-Thomas Biquad with poles at −1,000 ±8995.03? and DC gain of 1.87. In your final design, the capacitor value should be 0.01uF.
A high-pass filter is to be designed for speech signal processing. The cutoff frequency is 3.4kHz and the gain to be 10.0 in the passband. At 340Hz, the gain is desired to be less than or equal to 0.1% of the gain at 3.4kHz. Please use Sallen-Key type of filters for this design and draw the complete circuit schematic and indicate the resistance and capacitance values.
Hello. I'm not sure how to get this practice problem going. Could you help? Thank you. Design 1st-order low-pass filters with cutoff frequency fc = 2 kHz and DC gain of 1 and 5. Inverted or not doesn’t matter. Use a 10 nF capacitor. (i) Draw the circuits, (ii) write the transfer functions and (iii) find the other component values. Don’t make it more complicated than it needs to be!
Design an active lowpass filter with dc gain of 0.5 and corner frequency of 250Hz. Then draw the circuit diagram for this filter.
The band-pass filter in the figure is f = 46 with a tolerance of 10%.It is required to pass signals at kHz frequency (for example,For a 100 kHz operation, the low cutoff frequency foL = 90 kHz andthe high cutoff frequency will be foH = 110 kHz). Accordingly, RG1470 Ω , RG2 = 560 Ω, RF1 = 1.2 kΩ, RF2 = 2 kΩ, C₁ = 0.05 µF andWhat should be the value of the resistors R₁ and R₂ respectively when C₂ = 0.03 µF
For the given filter circuit below fC is the 563, C is 1 μF the gain is -10find Rf anf Ri and name the frequency response of the filter