Power factor correction is a method to do which of the following. ⒸRaising the power factor to decrease the current being supplied to the load. O Supply more inductive reactive power to the system O Supply more inductive reactive power to the system by adding an inductive load in parallel to the load impedance.

Power factor correction is a method to do which of the following. ⒸRaising the power factor to decrease the current being supplied to the load. O Supply more inductive reactive power to the system O Supply more inductive reactive power to the system by adding an inductive load in parallel to the load impedance.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
Find the total impedance, total current drawn by the system, total power (apparent) delivered by the voltage source, Draw the phasor diagram of the voltage and current at the source.
For the circuit below, find the following: (a) Apparent power absorbed by the loads (i.e. impedances). (b) Real power absorbed by the loads and reactive - power absorbed by the loads. (c) Power factor seen by the source.
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
For the following network find a) Isb) PT, QT, ST and PFTc) Draw power triangle d) Raise the power factor to unitye) Compute Is after raising the power factor
Find the complex power for the following: Vrms= 200 ∠ 30∘ V, Z= 40+ j60 Ω in addition form
The three-phase balanced load system shown in the figure will be analyzed in a continuous sinusoidal state.a) Find the total active and reactive power consumed in the load, with vR (t) = Cost Volt, Z∆ = α + βj,Find the phasor values of Ir, Is and It line currents.b) C capacities are connected to the circuit in order to provide compensation, C capacityCalculate what the value should be. α=3, β=8
A 480V single phase load has resistance of 70 ohms and inductive reactance of -j45 ohms. Find the real power, the apparent power, and the power factor consumed by the load.