Power factor correction is a method to do which of the following. Raising the power factor to decrease the current being supplied to the load. Supply more inductive reactive power to the system O Supply more inductive reactive power to the system by adding an inductive load in parallel to the load impedance.

Power factor correction is a method to do which of the following. Raising the power factor to decrease the current being supplied to the load. Supply more inductive reactive power to the system O Supply more inductive reactive power to the system by adding an inductive load in parallel to the load impedance.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Similar questions

The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the positive terminal of the source. Determine the real and reactive power and state whether the source is delivering or absorbing each.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Find the total impedance, total current drawn by the system, total power (apparent) delivered by the voltage source, Draw the phasor diagram of the voltage and current at the source.
For the circuit below, find the following: (a) Apparent power absorbed by the loads (i.e. impedances). (b) Real power absorbed by the loads and reactive - power absorbed by the loads. (c) Power factor seen by the source.
A balanced positive-sequence wye-connected 60-Hz three-phase source has line-to-line voltages of VL = 440 V rms. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.5-H inductance in series with a 30-Ω resistance. Assume that the phase of VanVan is zero. FIND Ia,Ib,Ic, Find the power delivered to the load And Find the reactive power delivered to the load.
A 480V single phase load has resistance of 70 ohms and inductive reactance of -j45 ohms. Find the real power, the apparent power, and the power factor consumed by the load.
The three-phase balanced load system shown in the figure will be analyzed in a continuous sinusoidal state.a) Find the total active and reactive power consumed in the load, with vR (t) = Cost Volt, Z∆ = α + βj,Find the phasor values of Ir, Is and It line currents.b) C capacities are connected to the circuit in order to provide compensation, C capacityCalculate what the value should be. α=3, β=8