power of a signal is 10 watts and the power of noise is 1 microwatts. i. What is the SNR (signal-to-noise ratio)? ii. What is the SNR in decibel (dB)

Q: What is the difference between frequency modulation and phase modulation?   DO NOT COPY FROM THE…

A: Frequency modulation Phase modulation Frequency changes at the instant but phase and amplitude…

Q: A low-pass analog signal of 4 kHz. If we send the analog signal, we need a channel with minimum…

A: Given: Analog signal frequency, fm=4 kHz After signal is digitize, 8 bits per sample is sent.

Q: If the output voltage of an amplifier is 1.2 V rms and its voltage gain is 50, what is the rms input…

A: The solution is given below

Q: You are required to generate an AM signal based on below equation. Vc (t) = 2 sin [2r(50x103 )t ]V…

A: As per our guidelines we are supposed to be answer only first 3 subparts. Kindly repost the other…

Q: Vo0 = 5V VT=0.2 Ry vo Un = 133 Ma Cgd= 02PF 220F MI= M2= NMOS Rsig-100 Ru = 25 midband ua itage gain…

A: Given the circuit: Given the parameter values: VT=0.2 V, Kn=1.33, gm=0.4 mS, Cgd=0.2 pF, Cgs=2.2…

Q: Complete the above table and plot the phase shift (Calculated) vs frequency (KHz) graph. Q- From…

A: Given the circuit: Given the table: 1. We need to complete the table and need to plot the…

Q: Which signals are function of time? * O None of the mentioned OF(w) O Random signal Power spectral…

A: Ans . Random signal

Q: R1) a) Calculate the essential bandwidth W (in Hz) of the signal 3eu(t) if W is required to contain…

A:

Q: Determine the maximum signal frequency in kHz that may be used for the circuit show below with…

A:

Q: 2. What would be the frequency of a signal with a period of 0.1057? 3. A signal of 5 volts is…

A:

Q: It happens when a signal's amplitude-versus-frequency characteristics at the receiver's output…

A: 1) Phase distortion happens when the phase response of the filter changes nonlinearly across the…

Q: 4. A 1" order system has a time constant of 100ms. If the input signal diagram shown below, plot the…

A: A first order system has a time constant of 100 ms. If the input signal has the frequency diagram as…

Q: Design an Armstrong indırect FM modulator to generate an FM carrier with carrier frequency of…

A:

Q: What is the function of transmitter

A: Transmitter: Transmitter is a electronic device. It is widely used in telecommunication.

Q: A receiever tunes from 20 to 40 MHz using a 10.7-MHz IF. Calculate the required range of oscillator…

A: Given f1 =20 MHzf2 =40 MHzIf =10.7 MHz

Q: A signal travels through an amplifier, and its power is increased 100 times. What is the attenuation…

A: In this question we need to find a attenuation in decibel

Q: An AM signal has the equation: v(t) = {20 + 8sin(40 x 103t)}sin(30x 106t) V (a)    Find the carrier…

A: The solution is given below

Q: . Given a receiver with a 100-kHz bandwidth and an effective noise te perature of 600 K, what is the…

A:

Q: Please write introduction four-line and conclusion two-line . for lab report about: (Fundamentals of…

A: Fundamentals of AC       It means alternating current.       It have the same frequency for current…

Q: A Fimd X[n] from frequency sigal by usingIf Engineering & numerical analysis

A:

Q: A sampling system and the spectrum of the corresponding input signal are given as follows. The…

A:

Q: If the signal-to-noise ratio is 15 dB and the noise power is 10 pW, find the signal power.

A: we need to find the signal power

Q: A sampling system and the spectrum of the corresponding input signal are given as follows. 50(t –…

A:

Q: The relation between analog frequency 'F and digital frequency 'f is? a) F=f*T(where T is sampling…

A: Given, Analog frequency is F Digital frequency is f

Q: What is the Nyquist sample rate for a voice input of 10 kHz?   Select one: a. 10 kHz b. 20 kHz c.…

A: In this question,  We need to choose the correct option.  What is the Nyquist sample rate for a…

Q: The attenuation of a signal is -10 dB. What is the final signal power if it was originally 5 W?

A: Attenuation means degradation of output power with respect to the input power because of some losses…

Q: an we obtain a plot of XL against frequency f experimentally

A: Inductance- Inductor twists in many turns are called inductor or coil inductance does not depend…

Q: Find the bandwidth of a commercial FM transmission if the frequency deviation is 75 kHz and the…

A: According to Carson's bandwidth formula, the bandwidth for a commercial FM transmission can be…

Q: What is the unit of bandwidth of FM

A: The solution is provided in the following section.

Q: Consider the FM signal s(t) = 5cos(π80000t + 20sin(π1000t)). What is the modulation sensitivity if…

A: It is given that: s(t) = 5cos(π80000t + 20sin(π1000t)) V=10 Volt

Q: During the measurement, power signal from sensor reading is 10 dB (decibels), and the noise power is…

A: "According to the Company's policy, we will solve the first subpart of the question since the other…

Q: The plot of amplitude of a signal as function of frequency is termed as

A:

Q: An audio signal consists of frequencies in the range of 100Hz to 5.5KHz.What is the minimum…

A:

Q: 1. Explain the principle of the sonic log.

A:

Q: Q5: Design an Armstrong indirect FM modulation to generate an FM signal with carrier frequency 97.3…

A:

Q: Essay. 1. What are the advantages of FM over AM? 2. What are the advantages of AM over FM? 3. What…

A: As per guidelines we are supposed to answer only first 3 questions so please upload other questions…

Q: 9. If the output voltage of an amplifier is 1.2 V rms and its voltage gain is 50, what is the rms…

A: Given, Output voltage, Vo=1.2 Vrms Voltage gain, AV=50 RMS input voltage, Vin=?

Q: 1. A 50- resistor operates at room temperature (25°C). How much noise power does it provide to a…

A:

Q: power of a signal is 10 watts and the power of noise is 1 microwatts. What is the SNR…

A:

Q: 1. In a transistor amplifier how is a small ac signal defined? 2. Why are capacitors and voltage…

A: We need to answer in a transistor amplifier how is a small AC signal defined. Also we need to…

Q: The value of the decibel is positive, if signal is Amplified explain?

A:

Q: Q5- If an information signal x ( t ) = cos(2π700t) +10cos(2π5000t) . Write the formula ofthe…

A:

Q: Design (only the block diagram )an Armstrong indirect FM modulator to generate an FM carrier with…

A: According to the given parameters narrow band FM has fc (carrier frequency)=100 khz triangle f =10…

Q: Q3) A Channel with bandwidth of 3MHz and noise 1.5 µW. If a signal of 2mW is transmitted what is the…

A:

Q: 4.15 An audio signal has a bandwidth of 15 kHz. The maximum value of |m(t)| is 10 V. This signal…

A:

Q: The noise level measured at a particular location in a factory with a noisy machine operating nearby…

A: Given parameters are: The noise level measured at a particular location in a factory with a noisy…

Frequency Modulation

Frequency modulation is a method or process of encoding the data of a specific signal (analog or digital) by modulating the carrier wave frequency according to the frequency of the modulated signal. Modulated signals are nothing more than information or data that should be conveyed after being converted into electronic signals.