Activity 9: What's My FunctionDirections: Write on the space provided before each item the name of the parts of the electricpower transmission based on the given function.GENERATORPOWER PLANTSTEP-UP TRANSFORMERDISTRIBUTION STATIONTRANSMISSION SUB-STATIONSTEP-DOWN TRANSFORMER1. It reduces the voltage further into a more manageable 2,300 volts.2. Brings down the voltage to about one-fifth of the incoming voltage.3. The generating plant that produces power and voltage at 6,600v.4. The 2,300v are finally brought down to 220v to 230v for householdconsumption5. Increases the voltage to as high as 132,000 volt which necessary due tothe resistance of the conducting wires.

Answered: power transmission based on the given…

Engineering

Electrical Engineering

power transmission based on the given function.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter15: Dryer Outlet, Lighting, And Receptacle Circuits For The Laundry, Powder Room, Rear Entry Hall,and Attic

Section: Chapter Questions

Problem 18R: A residential air-conditioning unit is installed in the attic. a. Is a lighting outlet required?...

See similar textbooks

Related questions

Q: Calculate work-function difference at T=27°C between Aluminum (4.1eV) and Boron doped Silicon.…

Q: 1- A 200-kVA transformer has an efficiency of 98 % at full-load. If the maximum efficiency occurs at…

Q: 10. A flashlight with four 1.5 VDC batteries in series with a bulb that has resistance of 18 ohms.…

A: Given, A flashlight with four DC batteries with emf, ε=1.5 V All batteries are in series with a bulb…

Q: A transmitter has an alphabet of four letters [x1, x2, x3, x4] and the receiver has an alphabet of…

Q: A 600 kVA, 1-ph transformer has an efficiency of 92 %

A: Transformer- A device that transfers the electrical energy between two electrical circuits which are…

Q: ↓= R1 200 ww + V1 40 V 511 H R3 40 R2 2002 www R8 200 ww R4 210 R5 R6 200 R7 200 B

A: The solution is given below

Q: 4. A circuit has a transfer function (8+1) H(s)-(² +65 +25) a. Determine the partial fraction…

A: A circuit has a transfer function: H(s)=s+1s2+6s+25 a) We need to determine the partial fraction…

Q: Find the Fourier Series Representation of f(eitheta) = 1/13-12 cos(theta

Q: Draw the Vs and is as a function of time when the switch on at t=0 R3 S2 Vs Rr=00 Ro -E к

A: Here we have got a DC source voltage and a purely resistive circuit. Since there is no inductor and…

Q: Find the Q point value of the diode current and the voltage gain Av in the following circuit: 700Ω…

A: Diode It is an unidirectional electrical device, which allows current to flow only in one specific…

Q: Given the circuit below, compute for the following, (fin = 60Hz) a. Peak to peak ripple b. Filtered…

A: In this question, We need to determine the peak to peak ripple voltage and filtered dc value? We…

Q: 3.- (33) Find the h parameters for I₁ I₂ ww V₁ N R₁ R₂ V₂ the given circuit

A: In this question, We need to determine the h parameters for the given circuit. Using the virtual…

Q: Draw the output voltage waveform. V; 100 V –100 V 2.2 ΚΩ Ideal diodes 2.2 ΚΩ να 2.2 ΚΩ +

Q: A discrete-time signal x[n] has a period of N > 2. Which of the following is/are always true about…

Q: Determine and carefully sketch the even and odd parts of the function shown in Figure 1.

Q: can you give a expanded solution on how you solve eq 1,2, and 3?

A: After applying KVL in the meshes, we get the following set of 3 independent equations:…

Q: Given the magnetic field vector potential: A= y z ax +2 x y z ay-xz az (A/m), find: (1) magnetic…

Q: 21 Given the equation, ve = 42.1 V sine, What is the value of Vrms? O %3D 42.1 V 84.2 V 59.54 V…

A: In this question we need to choose a correct option

Q: For the next 3 questions, consider the circuit below. VTH = 4V and k = 1 mA/V² +12V Vo 100 viam If…

Q: If a 3 phase inverter is feeding an appliance that is rated as 207v AC, 60Hz, 100kVA, compute the…

A: It is given that: Vacline=207 Vf=60 Hzma=1

Q: 5.18. A small DC machine has an armature resistance of 4 ohms. Under no-load conditions when…

A: Solution

Q: FIND THE TOTAL FLUX DENSITY IN REGION: 1 <=Y <= 10 1 <= Z <= 2 X=0 If an infinite current sheet of…

A: It is given that: 1≤Y≤101≤Z≤2X=0k=3ay

Q: 1. Consider the discrete-time signal x[n] illustrated in Figure 1. -1 -202 6 8 n Figure 1 (a)…

A: According to the question, for the given graph of x[n] as shown below (a) Sketch the magnitude…

Q: Consider the circuit shown in figure. The circuit uses an ideal operational amplifier. Assuming that…

Q: For the network below, VD = 9 V. Determine: ID. VS and VDS. VG and VGS. VP. 18 V 2 kN 750 k2 A6 = 1…

A: We need to find current and voltage for given circuit

Q: Solve for Id and Vo.

A: The voltage drop across and current through the diode can be calculated by using Kirchhoff's laws.…

Q: d. If V2 = 8 V and E = 14 V, find V3. e. If R1 = 4 Ω, R2 = 2 Ω, R3 = 4 Ω, and R4 = 6 Ω, what is RT?…

A: If V2 = 8 V and E = 14 V, we need to find V3. Applying KVL in the loop, -E+V2+V3=0,-14+8+V3=0,V3=6…

Q: Calculate the output voltage if V1= 2V and V2 = 1V for the circuit: Vo=____Volts

Q: Represent Vrms = 120V as a voltage equation O v(t) = 120 V sin(360° x t x f) O v(t) = 84.85 V…

Q: Make a figure/schematic symbol/drawing of this 2 problem given below (Parallel method: includes…

A: Bulb 1, 2 and 3 controlled by switch 1 in a parallel connection, Bulb 4 controlled by switch 2 in…

Q: Draw the voltage vm as a function of time when Zo = Ro = 500 for figure shown 50Ω S3 ↑ 5002 个个 Vs Vm…

A: In this question we need to draw Vm as a function of time

Q: 2. Determine the Q waveform for the flip-flop as seen in the figure below. Assume that Q = 0…

A: In this question, We need to draw the output waveform of the JK filp flop. If initially Qn = 0

Q: P8.7 A stepper motor has a specification of 200 steps/revolution. The motor shaft drives a linear…

A: A stepper motor has a specification of 200 steps/revolution. The motor shaft drives a linear…

Q: The characteristic impedance of a transmission line is 70 ohms and has a load of 35 ohms. The SWR…

A: The solution is given below

Q: 1. What are the basic components of RC Oscillator Circuit? 2. How is the resonant frequency being…

A: As per the guidelines of bartleyby I need to answer first three questions only.

Q: Draw the voltage vm as a function of time when Zo = Ro = 500 for figure shown www 50Ω O S3 个个 502 Vs…

A: In this question we need to draw Vm as a function of time

Q: A three-phase induction motor has the following parameters: Uc 380V,

A: Three Phase Induction machine- This Induction machine comprises of rotor and stator as it basic…

Q: Find the VTH using thevinen theorem

A: In this question, We need to determine the Thevenin voltage across the terminal a and b.

Q: Question 1 a. Using the step-invariant method, obtain the discretized form of the state equation for…

A: The minimum time control problem involves finding a control policy that will drive the system…

Q: Draw the voltage vm as a function of time when Zo = Ro = 500 for figure shown www 50Ω S3 个 502 ↑ Vs…

A: In this question we need to draw Vm as a function of time

Q: If the input voltage in the figure below is increased, the peak negative value of the

A: Diode- When diode is forward biased it is short circuited in a circuit ideally. When diode is…

Q: Consider the circuit shown in figure. The circuit uses an ideal operational amplifier. Assuming that…

A: The solution is given below

Q: 1. What are the basic components of RC Oscillator Circuit?

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Hint: Look for the expression of the current at resistor 1 and resistor 2 before you proceed to the…

Q: In the circuit shown below, the op-amps are ideal. Then Vout in volts is 1 ΚΩ 1 ΚΩ -2 VoM Μ +15 V…

Q: 7. In a WYE configuration, Line to Line voltage is equal to

A: WYE Connection(Y-Connection): It is also called Star Connection. The Star Connection (Y) Method,…

Q: Draw the voltage vm as a function of time when Zo = Ro = 500 for figure shown 5002 S3 个人 502 Vs Vm…

A: In this question we need to draw Vm as a function of time

Q: Q10/ In a single integration DM scheme, the voice signal is sampled at a rate of 64 kHz. The maximum…

A: We need to find out step size to avoid the error

Q: Draw the voltage vm as a function of time when Zo = Ro = 500 for figure shown www 50Ω O S3 个个 502 Vs…

A: In this question we need to draw Vm as a function of time

Q: Vin R3 10. If Vin= 14V, Vz= 6.1V, Vae = 1.1V, he = 50 then, VOUT = V L = Ic= MA MA MA R2 250 R1 750…

A: We need to find out voltage and current for given circuit

Question

Activity 9: What's My Function
Directions: Write on the space provided before each item the name of the parts of the electric
power transmission based on the given function.
GENERATOR
POWER PLANT
STEP-UP TRANSFORMER
DISTRIBUTION STATION
TRANSMISSION SUB-STATION
STEP-DOWN TRANSFORMER
1. It reduces the voltage further into a more manageable 2,300 volts.
2. Brings down the voltage to about one-fifth of the incoming voltage.
3. The generating plant that produces power and voltage at 6,600v.
4. The 2,300v are finally brought down to 220v to 230v for household
consumption
5. Increases the voltage to as high as 132,000 volt which necessary due to
the resistance of the conducting wires.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A homeowner wants to add 12 general-purpose receptacle outlets to the electrical drawings before the house is built, what additional load, in volt-amperes will they add to the service load calculation?
A 300-kilovolt-ampere transformer bank consisting of three 100-kilovolt-ampere transformers has a 3-phase, 480-volt delta primary and a 120/240-volt, 3-phase, 4-wire delta-connected secondary.For problems 1 through 4 show calculations and/or source of information. 3. What is the proper rating of the fuses to install for overcurrent protection of the secondary?
Refer to the National Electrical Code or the working drawings when necessary. Whereapplicable, responses should be written in complete sentences.A 300-kilovolt-ampere transformer bank consisting of three 100-kilovolt-amperetransformers has a 3-phase, 480-volt delta primary and a 120/240-volt, 3-phase, 4-wiredelta-connected secondary.For problems 1 through 4 show calculations and/or source of information. 1. Sketch the secondary connections, and indicate where a 120-volt load couldbe connected.
Refer to page 30, the single line diagram shows 1000 kVA. if the transformer capacity rating to be used is 1500 kVA at 480 volts, and the second transformer rated 225 kVA be changed to 250 KVA at 208 volts, calculate the fault at X1 and fault at X2. Assume all other data are the same.
Refer to the National Electrical Code or the working drawings when necessary. Whereapplicable, responses should be written in complete sentences.A 300-kilovolt-ampere transformer bank consisting of three 100-kilovolt-amperetransformers has a 3-phase, 480-volt delta primary and a 120/240-volt, 3-phase, 4-wiredelta-connected secondary.For problems 1 through 4 show calculations and/or source of information. 1. What is the proper rating of the fuses to install for overcurrent protection of thesecondary?2. What is the kilovolt-ampere of the bank if one of the transformers is removed?
5. How many system bonding jumpers normally are there for a separately derived system that's grounded? A. ThreeB. TwoC. One D. Zero 6. How many grounded neutral conductors are in a 208Y/120 volt, 3-phase, 4-wire system? A. ThreeB. TwoC. One D. Four 7. Which of the following are sometimes installed as an emergency system, legally required standby system, or optional standby power system for a building or structure? A. GeneratorsB. Surge protection devices C. Surge arrestersD. Transformers 8. If the system bonding jumper in a DC system is a screw, what color must the screw be? A. WhiteB. RedC. Orange D. Green 9. If overcurrent protection is provided in the transformer of a separately derived system, which of the following statements is correct? A. An equipment grounding conductor must be run with the conductors between the transformer and the building's disconnect. B. There's no need for service equipment or a panelboard in the separate building.C. A ground electrode must…
List the equipment in detail with rating for substation and swictchgear installation.
______ protection of equipment shall be provided for solidly grounded wye electrical services of more than 150 volts to ground, but not exceeding 600 volts phase-to-phase for each service disconnecting means rated 1000 amperes or more. Select one: a. arc-fault b. short circuit c ground-fault d. double
16. Flexible metal conduit will be installed between a raceway and a transformer in a system. If it's to serve as an equipment grounding conductor, the flexible conduit and its fittings must be less than _______ feet. A. 2 B. 6 C. 10 D. 4 17. In which of the following situations can an equipment ground conductor be run separately from the circuit conductors? A. When you install a GFCI and are connecting additional receptaclesB. When the connection is to be made to a nearby water pipeC. When you're replacing an ungrounded two-wire receptacle with a grounded receptacle D. When there are no spare conductors in the cable 18. A 400-amp circuit breaker protects a feeder that's installed in a nonmetallic raceway that requires an equipment grounding conductor. Which of the following is the minimum size of aluminum equipment grounding conductor that should be used in this situation? A. No. 4B. No. 1C. No. 6 D. No. 2 19. Which of the following is bonded to the grounding electrode system…
In the conduit diagram shown in Figure 1–3, determine how many wires are in each conduit between each piece of equipment. Identify each wire terminal connection and the quantity of wires, as shown in the example, above the disconnect switch.
list the material required for overhead service connection
Larger conductors should be used for long runs to minimize the? A. Current B. Voltage drop c. Transformer retio d. Interrupt rating