PRACTICE PROBLEM 2.4: Find vi and v2 in the circuit. 12 2 shown in Figure below. Also calculate i and iz and the power dissipated in the 12-2 and 40-2 resistors. 15 V 10 2 40 Answer:v = 5 V, ij = 416.7 mA, pi = 2.083 W, v2 = 10 V,i2 = 250 mA, n = 2,5 W.

PRACTICE PROBLEM 2.4: Find vi and v2 in the circuit. 12 2 shown in Figure below. Also calculate i and iz and the power dissipated in the 12-2 and 40-2 resistors. 15 V 10 2 40 Answer:v = 5 V, ij = 416.7 mA, pi = 2.083 W, v2 = 10 V,i2 = 250 mA, n = 2,5 W.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: PRACTICE PROBLEM 2.4: Find v, and v; in the circuit shown in Figure below. Also calculate i, and i,…

A: To solve above problem, one should know about Kirchhoff's law.There are two Kirchhoff's law.KCL: It…

Q: For the circuit shown in Fig. 2.45, find: (a) vị and v2, (b) the power dis- sipated in the 3-k2 and…

A: The solution can be achieved as follows.

Q: In the following circuit, element 1 absorbs 28 W, element 4 supplies 24 W, voltage across element 3…

Q: U2 in the circuit shown in Fig. 2.43. Also calculate 1 and iz and the power dissipated in the 12-N…

A: V-156+V-1512+V10+V40=02V-30+V-1512+4V+V40=03V-4512+8V40=03V-4512+V2=06V-90+3V=09V=90V=10 Volts Using…

Q: Q1 * UTM UTMA) Based on electrical DC circuit as depicted in Figure Q1(a), 5 UTM UTM Determine the…

Q: Exercise 2-1 a) Find the currents I1, I2, and Iz in the circuit shown in Figure. b) Find the…

Q: (e) Suppose node f in Figure 2 is connected to ground, and the elements in the circuit have the…

A: Consider the given circuit,

Q: Find vi and vz in the circuit shown in Fig. 2.43. Also calculate i, and iz and the power dissipated…

A: In the given circuit, 12Ω resistor and 6Ω resistor are connected in parallel and 10Ω resistor and…

Q: 4) In a voltage source: a) Current flow from -ve terminal to +ve terminal inside the battery b)…

Q: 50 102 H.W. 2.7: Determine the current supplied by each battery in the circuit shown in Figure by…

A: To determine the current

Q: a) Analyse the circuit provided in Figure 2 to determine the Ig, Ig , Vo V, and Vg using exact…

A: NOTE: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: Find /and the power absorbed by each element in the network. Consider element 1= 6 V, element 2=3 V,…

Q: Part E - Calculating currents in a resistive network For the circuit shown, calculate iz, i, ig, and…

A: I used the nodal analysis instead of resistance reduction techniques as you mentioned in the…

Q: Find vy and vy in the circuit shown in Fig. 2.43. Also calculate i, and iz and the power dissipated…

A: we will use nodal analysis to calculate node voltage V2. then we will calculate other branch…

Q: Problem #2: Use Tellegen's Throrem (not Nodal Analysis) to calculate current 13 flowing along branch…

Q: Find vị and vz in the circuit shown in Fig. 2.43. Also calculate i, and iz and the power dissipated…

Q: Problem 2 2Vx Refer to figure 2. a) Reduce the circuit so that when using nodal analysis, four node…

A: Nodal Analysis : The technique of calculating the voltage between "nodes" in an electrical network…

Q: Find vị and vz in the circuit shown in Fig. 2.43. Also calculate i, and iz and the power dissipated…

Q: Practice Problem 2.12 Find v, and v2 in the circuit shown in Fig. 2.43. Also calculate i, and iz and…

Q: HW2.2 – In the DC circuit, source voltage is given as vz = 120 Volt. Dete 80 Ω 25 i 20 N 10 210 03 §…

A: In this question , we will find current and voltages..

Q: 1 122 -ww Find v and vz in the circuit shown in Fig. 2.43. Also calculate i, and iz and the power…

A: using KCL we will find voltage across 10 ohm resistor . By using ohms law we will find current in…

Q: Practice Problem 2.12 Find v, and v, in the circuit shown in Fig. 2.43. Also calculate 1 and iz and…

Q: 12 2 PRACTICE PROBLEM 2.4: Find vi and v2 in the circuit ww shown in Figure below. Also calculate i,…

A: To find the current, voltage and power

Q: 2.10 The current is in the circuit shown is 2 A. Calculate a) v b) the power absorbed by the…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: For the power system shown below, find the short circuit level and short circuit current at F. Take…

A: In the powerr system Find the short circuit level and fualt current at the point F. Per unit…

Q: Find and vz in the circuit shown in Fig. 2.43. Also calculate 1 and Practice Problem 2.12 iz and the…

Q: 4 8 V1 V2 R1 16 8V 5V

A: Given V1 =8 VR1 =16 ΏR2 =4 ΏR3 =8 Ώ V2 =5 V

Q: 2. Determine the following (a) Looking back resistance at load R. (b) Current in the Load Resistance…

A: In this question, Determine (a) Looking back resistance at load R. (b) Current in the Load…

Q: Example: Hnuw For the circuit shown.infigure below, find the equivalent resis tance and…

Q: For the circuit shown in Fig.2 (c) i2, and (d) the power supplied by the voltage find (a) i, (b) v,…

A: The given circuit is

Q: Eo A Ry Ruo Ifz © Ro Rq Mz Ma My M5 B E, = 200 (V) If2 = 2 (A) E, = 100 (V) If. = 4 (A) R = R2 = 5…

A: Fhhh

Q: Find vy and vz in the circuit shown in Fig. 2.43. Also calculate i, and iz and the power dissipated…

A: Applying KCL at node(at 10 ohm resistor) gives node voltage. Using ohms law we will find currents I1…

Q: In the following circuit, element 1 absorbs 28 W, element 4 supplies 24 W, voltage across element 3…

A: P ∞ V2 SO, P2/P3 = (V2/V3)2 P2 = P1 + P3 + P4

Q: H.W. 2.12: Calculate v1, ij, v2, and i, in the circuit of Figure below. Solution:v,= 12 V, i=3 A, 4…

Q: Find v, and Uz in the circuit shown in Fig. 2.43. Also calculate i and i, and the power dissipated…

Q: Problem 2 Consider the circuit in Fig. 2 and perform the following: a. Calculate the voltage across…

A: In the network, 2 independent voltage source and resistance are consist. Find the current and…

Q: a) Find the equivalent resistance observed between the terminals a and b. b) If a voltage source of…

Q: For the circuit as shown in the figurel, Find V, and the power supplied by the 25V source. 10V 5KQ…

A: 1.. Across 6 ohm resistance voltage is Vy. But this 6 ohm resistance is short-circuited by a wire…

Q: Q1: For the network of Figure below, VDD= 9 V. Determine: (a) ID. (b) VS and VDS. (c) VG and VGS.…

Q: Given the circuit shown in Figure Q1: (i) If R₁ = 5 km2, determine the current I₁ flowing through…

A: For part i and ii we will apply nodal analysis and ohm's law For part (iii), maximum power we gets…

Q: For the circuit shown in Fig. 2.45, find: (a) vi and v2. (b) the power dis- sipated in the 3-k2 and…

A: The equivalent resistance is given by, 1RT=1R1+1R2+1R3=R2R3+R1R3+R1R2R1R2R3RT=R1R2R3R2R3+R1R3+R1R2…

Q: Find v and v2 in the circuit shown in Fig. 2.43. Also calculate 1 and iz and the power dissipated in…

Q: ECE 211 Electric Circuits I Circuit Design Project Part I Design the circuit shown to get the value…

Q: 1. If R1 = 20, R2 = 42, R3 = 62, determine the electric current flows in the circuit below. Known :…

Q: For the circuit shown in Fig. 2.45, find: (a) v, and v2, (b) the power dissipated in the 3-k2 and…

A: In the question given a circuit and we have to solve that circuit to find the values (a) v1 and v2,…

Q: 4- For the circuit shown in Fig.2, when E=12 V the voltmeters read as follow: VI=5 V, V2= IV, V3= 2…

A: We will use ohm's law to calculate the values of resistors and when the voltage V3 is changed to 6…

Q: PRACTICE PROBLEM 2.4: Find y, and v2 in the circuit shown in Figure below. Also calculate i, and i₂…

Q: Problem 2 2Vx Refer to figure 2. a) Reduce the circuit so that when using nodal analysis, four node…

A: Nodal Analysis : The technique of calculating the voltage between "nodes" in an electrical network…

Q: Practice problem 2.6: Find the currents and voltages in the circuit shown below. Answer: v₁ = 3 V,…

Q: Kirchhoffs Law Determine/Compute for > Nodes > Branches > Loops > KCL Equation > KVL Equation *Loop…

Question

100%

PRACTICE PROBLEM 2.4: Find vi and v2 in the circuit.
1 12 2
shown in Figure below. Also calculate i and iz and the
power dissipated in the 12-2 and 40-2 resistors.
15 V
10 2
40 2
Answer:v = 5 V, ij = 416.7 mA, pi = 2.083 W, v2 10 V.i2
%3D250 mA, p2 = 2.5 W.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
Using Kirchhoff's Rules, compute the current (mA) and voltage (V) values of the circuit if R1=2kΩ and R2=7kΩ.
1. Which resistance(s) has no effect on the value of vo? a. 4 ohms b. 260 ohms c. 16 and 260 ohms d. 40 ohms 2. What is the short circuit current (in amperes) when solving for the Thevenin equivalent circuit as seen by the 250Ω resistor? 3.Using superposition to get the Thevenin voltage (in volts) seen by the 250Ω resistor, what is the contribution by the 1A source?
In the figure, the K mechanical switch is switched from 1 to 2 at t = 0. In short, the load remained connected to the 2A current source for a long enough time. a) Obtain instantaneous value expressions of Vr and VL voltages in the new state. b) After t = 0.5 s, calculate the values of the voltage at the resistor ends of the circuit element. Obtain the instantaneous expressions of current and voltages.
The node voltage equation for node b is to be expressed in the form: K=A⋅Va+B⋅Vb+C⋅Vc, where A, B, C, and K are constants. If K=3, what should be the value of the coefficient B? what will be the value of the coefficient C?
A solar cell with a reverse saturation current of 5 nA is illuminated such that the short-circuit current is Isc = 200 mA.a. Plot I-V and obtain the voltage at maximum delivered power.b. Assume that this cell has a series resistance of 1 Ohm, so that the cell voltage is reduced by the IR drop. Replot the I-V curve for this case and compare with the plot in a.
Using Kirchoff's voltage law to determine the unknown voltage E2 for the configuration given in the figure below. Given that: - The source E1= 110 VV, - V1= 23.5 V, V2= 18 V, V3= 16.4 V, and V4= 20.5 V
For the circuit shown in Figure P2.37, finda. The equivalent resistance seen by the source.b. The current i.c. The power delivered by the source.d. The voltages v1 and v2.e. The minimum power rating required for R1.Given: v = 24 V, R0 = 8 , R1 = 10 , R2 = 2 .
1. Prove Vgsq= -1.9 V, Idq= 2.8 mA, re= 6.5 ohms 2. Prove that Av1 = -1.77, Av2 = -338.46. Show solution on how it arrived to these values. Thanks
a) The power, P, consumed by a resistor of resistance R, is given by P = E^2R Given that E = 20 V and R = 1000ꭥ, using partial derivatives, find the approximate change inpower if E is decreased by 0.5 V and R is increased by 50ꭥ.b) Check and compare your findings using standard electrical principles.
Find the Nortons equivalent source with respect to terminals A and B for the circuit shown inFig. 15.54. Hence, find the voltage VL across the 100Ω load and check its result by using Millman’s theorem. All resistances are in ohms.
Question: In the circuit to the right, R1 = R2,W/L = 3, Vtn = 0.6 V, and Kn = 200 A/V2. Determine the values of R1 and R2 such that VD = 1 V and Vs = -1 V.