The column below is made of A-36 steel (E=29,000 ksi, and= 36 ksi). The columns cross-section is shown on the right side.Prob 5.X-section viewoyieldDetermine the following:(a)(b)1 inTFind the moment of inertia about the x-axis (Im).Find the moment of inertia about the y-axis (I,).Which M.of.l controls?Find the largest critical load the column can support if the10 in X.18 ft(d)column is pin-pin connected (K=1.0)in1iny!6 in

Given Data:A-36 steel.E= 29000ksi.σyield= 36 ksi.H= 18 ft.

Prob 5. The column below is made of A-36 steel (E=29,000 ksi, and = 36 ksi). The columns cross-section is shown on the right side. X-section view oyield Determine the following: (a) 1 inI Find the moment of inertia about the x-axis (I,). Find the moment of inertia about the y-axis (I,). Which M.of.l controls? Find the largest critical load the column can support if the (c) (d) column is pin-pin connected (K=1.0) 10 in X. 18 ft 1 in 1inT[ yi 6 im

Prob 5. The column below is made of A-36 steel (E=29,000 ksi, and = 36 ksi). The columns cross-section is shown on the right side. X-section view oyield Determine the following: (a) 1 inI Find the moment of inertia about the x-axis (I,). Find the moment of inertia about the y-axis (I,). Which M.of.l controls? Find the largest critical load the column can support if the (c) (d) column is pin-pin connected (K=1.0) 10 in X. 18 ft 1 in 1inT[ yi 6 im

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bar DA is rigid and is originally held in the horizontal position. The wires are made of 304 stainless steel and have a diameter of 0.04 in. The weight W causes B to displace downward 0.06 in. Determine the downward displacement at C (in inches). E 5 ft 2 ft- 6 ft B A 6 ft W
3- For the beam given in the figure, a- Draw the elastic curve by using the Mohr Method. Calculate the values of A, B, VC, ec by using the Mohr Method. b- A 2EI 3 m B 3EI C I1m] 60Nm
Q2. (а) A beam is supported and loaded as shown in Figure Q2(a). Point A is a M 6 UTM pin support and point B is reactions at A and B. a roller support. Determine the support ITM M UTM 30 kN O UTM 80 kN/m 30 UTM UTM & UTM UTM :D M UTM 200 kNm 6 m В 12 m UTM TM UI *- *TTM FIGURE Q2(a) 3 UTM TM UTM *TTM
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. We know that Es=200 GPa and Eb = 105 GPa, calculate (a) the reactions at A and E, (b) the deflection of point C. Dimensions in mm -180- -120- GO KN 40-mm diam. G 1.00 100 DI Brass E 40 kN 30-imm diam.
SOLVE for components Fu and Fv. U 30° 40° F = 600 N V
The shaft S exerts three force components on the die D. Find the magnitude and coordinate direction angles of the resultant force. Force F, acts within the octant shown. Fy = 200 N Y60 F= 300 N 60 F = 400 N
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. We know that Es=200 GPa and Eb = 105 GPa, calculate (a) the reactions at A and E, (b) the deflection of point C. A Dimensions in mm 1.00 |--10-| 180-120- GO KN 40-mm diam, Bra D 100 40 kN 30-mm diam.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
3- For the beam given in the figure, a- Draw the elastic curve by using the Mohr Method. b- Calculate the values of A, B, VC, Oc by using the Mohr Method. A 2EI 3 m B 3EI C 1 m 60Nm
A solid 30.0-mm-diameter steel [E = 290 GPa] shaft supports two pulleys as shown. Determine the shaft deflection at point C. Assume that the bearing at point A can be idealized as a pin support and the bearing at point E can be idealized as a roller support. ... A B D E C 300 mm 200 mm 300 mm 200 mm 750 N 500 N (A -1.101 mm -0.936 mm -0.876 mm D) -1.586 mm E) -0.697 mm
A cantilever beam (member AC) is supported with a column (member CD). Force P is applied to Point B, which is located at the midspan of the beam AC. The column is required to prevent excessive deflection of the beam as shown below. Determine the ratio of internal force in the column (member CD) to the critical buckling load of the column (Pcr). The length for both of the members, L, is 1,650 mm. The applied force, P, is 240 kN. The flexural rigidity for the beam and the column, EI, is 4.0X107 kN·mm2.
A two-dimensional beam structure or frame (ABCD, shown below) has a concentrated load, P, acting on Point D. You can assume that the connections at B and C have sufficient strength to react the applied load and that loads and moments are transferred between the beams. You can assume that the members have a constant cross-section and that El-constant. B A 2m y L. C P-3kN D 2m In order to evaluate the design you must: (a) Sketch the deformed shape of the frame, solve the reaction forces and construct the bending moment diagram for the frame. (b) Use any method to determine the vertical deflection at Point D. Ensure that you clearly explain your approach and show your final answer. Clearly state any assumptions made. (c) If the bending rigidity, El, of the frame between Point B and Point C was doubled. What effect would this have on the resulting horizontal deflection at point D. Ensure that your answer is supported by suitable reasoning, calculations and/or sketches.