Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving wheel is 10 inches, and it revolves at 200 rpm. The width of the wheel is 2 inches. The force per inch width of face is 150 pound and the coefficient of friction is 0.20. a. 96 hp b. 23 hp c. 1.2 hp d. 1.6 hp

Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving wheel is 10 inches, and it revolves at 200 rpm. The width of the wheel is 2 inches. The force per inch width of face is 150 pound and the coefficient of friction is 0.20. a. 96 hp b. 23 hp c. 1.2 hp d. 1.6 hp

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
In an open flat belt drive, a pulley of 800 mm diameter runs at 300 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, the angle of lap is 170° and the maximum tension in the belt is 2000 N. The power transmitted is: 10.5 kW 9.4 kW 8.9 kW 7.6 kW None of the mentioned 13.1 kW
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
A double thread ACME screw driven by a motor at 534 rpm raises the attached load of 1,062 kg at a speed of 10 meters per minute. The screw has a pitch diameter of 36 mm. The coefficient of friction on threads is 0.15. The friction torque on the thrust bearing of the motor is taken as 20% of the total torque input. Determine the motor power required to operate the screw.
9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving wheel is 10 inches, and it revolves at 200 rpm. The width of the wheel is 2 inches. The force per inch width of face is 150 pound and the coefficient of friction is 0.20.
For a 90° V-twin engine system, having two identical cylinder with center line of each cylinder being inclined at 45° to vertical, the speed is 2400 rpm. The reciprocuting mass per cylinder - 1.5 kg stroke=14 cm length of connecting rod -28 cm. Find the values of max. primary and secondary Forces and indicate whether the same the can be balanced by suitable means.
Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm in 3 seconds. Calculate the heat generated for each engagement if clutch starting torque is 10 in-lb. a. 50 Btu b. 50 Btu c. 30.50 Btu d. 51.50 Btu
The belt drive in which pulleys rotate in the same direction is used to transfer power. The pulley diameters are 1.74m and 0.833m and it connects two parallel shafts which are 3.25m apart. The initial tension in the belt when it is stationary is 4500N. The smaller pulley is rotating at 710 rpm and coefficient of friction between the belt and pulley is 0.29. Determine the power transmitted by the belt drive
A ladder of length 5 m is resting against a smooth wall, its point of contact being just below a first floor window. The bottom of the ladder rests on the ground and the coefficient of friction between the ladder and the ground is 0.3. A person of mass 75 kg climbs the ladder, which has a mass of 4 kg. The bottom of the ladder is at the point of slipping, outward from the wall, just as the person reaches the mid-point of the ladder’s length. Draw a free body diagram of the ladder and calculate the maximum frictional force opposing the slipping motion. In addition, determine the angle of inclination (θ) of the ladder, when the person is at the mid-point and the ladder is on the verge of slipping.
.A steam engine develops power at mean torque of 18,000 N-m and velocity of 9 m/s. The mean diameter of the flywheel rim is 1.3 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.
Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The diameter of the larger pulley is ‘3’ m and that of smaller pulley ‘3’ m. The initial tension in the belt when stationary is ‘4’ kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at ‘700’ r.p.m. and length of the belt.
A leather-faced cone clutch has a contact surface with a mean diameter of 15 in. and transinits 20 hy turning at 800 rpm. For a cone angle of 20 degrees and a coefficient of friction 0.30, determine the force required to keep the surface in contact. Ans. 121.5 lb.