Problem 02 Determine the LRFD design strength and the ASD allowable strength for each of the compression members shown. Use the AISC Specification and a steel. a. W12 x 120 with KL =26 ft. b. HP10X 42 with KL = 20 ft. HSS 6 x 6 x 9 ft 3 in c. WT8 X 50 with KL=24 ft. W12 x 65 19 ft 6 in F, = 50 ksi 2.3 Fy= 40 ksi 2.1 Fy=40 ksi 2.2 Fy=50 ksi

Problem 02 Determine the LRFD design strength and the ASD allowable strength for each of the compression members shown. Use the AISC Specification and a steel. a. W12 x 120 with KL =26 ft. b. HP10X 42 with KL = 20 ft. HSS 6 x 6 x 9 ft 3 in c. WT8 X 50 with KL=24 ft. W12 x 65 19 ft 6 in F, = 50 ksi 2.3 Fy= 40 ksi 2.1 Fy=40 ksi 2.2 Fy=50 ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute the maximum service axial compression load permitted on the built-up cross-section of the accompanying figure. The load is 30% dead load and 70% live load. The steel used is A992, and the effective lengths are (KL)y = 14 ft and (KL)x = 42 ft.
A W16x 100 with Fy= 60 ksi is used as a compression member. The length is 13 feet. Compute the nominal strength for Kx = 2.1 and Ky = 1.0.
An axially loaded tied column must sustain the following service loads: Total dead load = 1600 kN live load = 1000 kN required strength, U = 1.2D + 1.6L reduction factor = 0.65 f'c = 28 MPa fy = 420 MPa determine the required number of vertical bars to be distributed equally on all sides of the column if the column is 500mm square using bar diameter = 20mm a. 8, b. 4, c. 10, d. 12
A built-up section consisting of W 350 x 90 with two 12 – mm plates welded to form a box section as shown in figure. The section is used as a column 10 meters long. The column is fixed at both ends, and braced at mid height about the weak axis (Y-axis). Use Fy = 248 MPa. a. Determine the effective slenderness ratio of the column with respect to lateral buckling about the x-axis. b. Determine the effective slenderness ratio of the column with respect to lateral buckling about the y-axis. c. Determine the axial load capacity of the column in kN.
A built-up section consisting of W 350 x 90 with two 12 – mm plates welded to form a box section as shown in figure. The section is used as a column 10 meters long. The column is fixed at both ends, and braced at mid height about the weak axis (Y-axis). Use Fy = 248 MPa a. Determine the effective slenderness ratio of the column with respect to lateral buckling about the x-axis. b.Determine the effective slenderness ratio of the column with respect to lateral buckling about the y-axis. c.Determine the axial load capacity of the column in kN.
Compute the design strength of the rectangular section beam if fy = 60ksi, f'c = 4ksi. The beam has 2 #7 compression bars and 4 #10 tension bars. Effective depth d = 22.5", beam width is 12". Express your answer in kip-ft and use two decimal places.
A 5.5m simple beam carries a uniform ultimate load Wu. The beam is laterally supported and has compact section. The properties of the section are: rx=105.16mm, ry=22.2mm, Sx=308000mm^3, Sy=35000mm^3, Zx=357000mm^3, Zy=55000mm^3, and Fy=248MPa. Calculate the ultimate load capacity Wu of the beam in KN/m considering flexure. Express your answer in 3 decimal places.
A W18 × 97 with Fy = 60 ksi is used as a compression member. The length is 13 feet.Compute the nominal strength for Kx = 2.2 and Ky = 1.0.
A W530x92 supports a uniformly distributed load of 12 kN/m (including the weight of the beam) and equal concentrated load P at quarter points (L/4, L/2, and 3L/4). The compression flange is laterally supported at quarter points and at the ends. The beam is 12m simply supported. Using A36 steel, the beam has the following properties: d = 533 mm bf = 209 mm tf = 15.6 mm tw = 10.2 mm k = 32 mm ry = 44.9 mm Sx = 2070 x 10^3 mm^3 Zx = 2360 x 10^3 mm^3 Es = 200,000 MPa Ix = 552 x 10^6 MPa Find the maximum allowable load P so that it will not exceed its maximum allowable moment capacity. Use conservative assumption for Cb.
Determine the flexural strength in ft kips of a W12 × 35 of A242 (Fy = 50ksi) steel subject to a. Continuous lateral support. Blank 1 b. An unbraced length of 10 ft with Cb = 1.0 c. An unbraced length of 20 ft with Cb = 1.0
The W350x90 section is used as a column as a column 10 m long. The column is fixed at one end and hinged at the other end. Braced at mid-height about the weak axis(y-axis). Properties of W350x90 are: bf=250mm Ix=266x10^6mm^4 d=350mm Iy=44.54x10^6mm^4 a)Determinethe critical effective slenderness ratio of the column. b)Determine the axial load capacity of the column using NSCP. please answer this, thanks ☺️
A T-beam section is to be designed to support an ultimate moment of Mu=600kN.m with compression in the flange of the beam. Using bf=650mm, hf=100mm, h=600mm, bw=400mm, f'c=21MPa, fy=415MPa, diameter of the bar=32mm, stirrups diameter=10mm, and concrete cover=40mm, calculate the following: Calculate the depth of compression block of the final section in mm.0 Calculate the ultimate moment capacity of the final section in kN.m.0 need solving in paper please thank you