PROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position shown if the breaking strength of the horizontal cable attached at C is T kN. Neglect friction. 4 Given: x = 1 m $ = 23° T = 15.5 kN W = kN (round off to 2 decimal places) 3.

PROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position shown if the breaking strength of the horizontal cable attached at C is T kN. Neglect friction. 4 Given: x = 1 m $ = 23° T = 15.5 kN W = kN (round off to 2 decimal places) 3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended from the r...

Q: In a hydraulic jump occurring in a horizontal channel, the Froude's number before the jump is 10.0 a...

Q: Find the reaction at points A and B below: 50k / ft 40 kip 50 kips- ft A В - 4.5 ft- 5ft- 8 ft-

Q: The base length of the runway at The mean sea level (MSL) is 1500 m. If the runway is located at an ...

Q: A retaining wall with a smooth vertical back retains a purely cohesive fill. Height of wall is 12 m....

Q: The footing of a wall is 1.5 m wide at the base and is located in a homogeneous cohesive soil at a d...

Q: The relative compaction of sand in the field is 95. The max dry unit weight of the sand is 16 kN/cum...

Q: Gives some example each problem about centrically and eccentrically bolted connection

Q: A vehicle travelling on a road with a velocity of 80 kmph possesses a kinetic energy of 85 kJ and ju...

Q: 10. The cable and pulley system shown is used by a camper to hoist a backpack into a tree to keep it...

A: Given data, Cable breaking strength of AB = 200 lb Cable breaking strength of AC = 200 lb DAE break...

Q: A homogeneous, prismatic beam shown in the figure has a weight of 4.7 KINM and is carrying a uniform...

Q: a. Find the support reactions b. Draw SFD and find the maximum shear force (magnitude) c. Draw BMD a...

A: Introduction: Share force- The algebraic sum of the vertical forces at any section of a beam to the ...

Q: A cantilever beam AB with a rectangularcross section has a longitudinal hole drilled throughoutits l...

A: The given beam is shown below:

Q: The results shown in the following table were obtained at the pea a series of CD TXC with a constant...

A: Step 1: σ3 = 70, 140 σ1 = σ3 + σd= 265+70, 494+140 = 335, 634 Horizontal axis is labeled normal stre...

Q: Trusses 1. Find the stresses of FAB, FAC, FBC & FBD- ( 20k 15k 60 60 Ra Rb

A: This question belongs to subject structural analysis. In this question find out stresses in members ...

Q: A convenience store has four available parking spaces. The owner predicts that the duration of custo...

Q: Determine the degree of staturation if void ratio is 0.62, water content 0.21 and specific gravity o...

Q: A steel penstock 500 mm in diameter has shell thickness of 10 mm. The modulus of elasticity of the s...

Q: A steel rod, circular in cross-section, tapers from 30 mm diameter to 15 mm diameter over a length o...

A: To determine the increase in length of the tapered steel rod. Diameter at the wider end (D) = 30 m...

Q: Item 1 Part A Determine the normal stress and shear stress acting on the inclined plane AB. Solve th...

Q: Replace the system of forces acting on the frame in the figure by a resultant R at A and a couple ac...

Q: Question Bank - Friction Two concrete blocks weighing 1800N each form part of the retaining wall of ...

Q: h=1.2 m H1=1 =0.8 Soil H2=2 m valve open In flow

Q: During a test of an airplane wing, the straingage readings from a 45° rosette (see figure) are asfol...

A: Given data: ε0=520×10-6ε45=360×10-6ε90=280×10-6

Q: 3) The free ends of two cantilever beams each of length L and flexural rigidity El are joined togeth...

A: In method of consistent deformation, Force is spring is considered unknown and compatibility equatio...

Q: Cars A and B are traveling in a section of a highway. Car B with a velocity of 20 m/s, and an accele...

A: The velocity of an object is the rate of change of its position with respect to a frame of reference...

Q: Find the reaction at points A and B below: 50k/ ft 40 kip 50 kips- ft A B 4.5 ft- 5ft- 8 ft-

Q: Given the existing components of each reaction with load P = 100 N. Determine the following: a.) The...

Q: The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If ...

Q: Completely determine the resultant with respect to point O of the force system shown in figure. 1414...

Q: The 6 m uniform rod as shown below weighs 1000 N. Segment AB and BC is 4 m long. The cable acts at a...

A: To Determine a.) The Reaction at Point A. b.) The Tension at Point D. c.) The Reaction at Point C.

Q: 4.0 N force is applied as shown in the figure below. Find the torque produced by this force with res...

Q: A steel bar of rectangular cross-section 50 mm × 60 mm is pinned at one end and fixed at the other e...

Q: True or false Topic: Quantity surveying 1. wherever possible, estimators should use prices based on...

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-part...

Q: 100 mm m 75 m 75 m

A: IXX = (dB3 )/12 Ixx = ( 150 x 1003 ) / 12 Ixx = 1.25 x 107 mm4

Q: An of highway weights empty and Ib when loaded. The weight distribution empty is 50% from and 50% re...

A: Given Data - Truck Weight = 70,000 lb ( empty) Truck weight = 150,000 lb ( when loaded) Weight distr...

Q: What is/are the important distinction between normal stress, shearing stress, and bearing stress fro...

A: Stress is a physical term that describes the force applied to a material per unit area.

Q: A simple curve of the proposed highway extension have a direction of tangents AB due North and BC wi...

Q: A tie bar 50 mm x 8 mm is to carry a load of 80 kN. A specimen of same quality steel of cross-sectio...

Q: A rigid steel container is partially filled with a liquid at 15 atm. The volume of the liquid is 1.2...

Q: Given data : Weight of dry soil=30 KN Weight of wet soil=40 KN Volume of soil=20 m3 Deterime Bulk un...

A: Given data : Weight of dry soil (WDry)=30 KN Weight of wet soil (WWet)=40 KN Volume of soil (V)=20 m...

Q: It is supported by a rod with a cable at point B. Determine the following: a.) The Tension at Point ...

Q: A five story auditorium building (with occupant load of 300) in Calstate LA campus has a steel speci...

Q: The probability that a smoker wants to quit smoking is 28%. Find the probability that in a randomly ...

A: Answer. d. 0.264

Q: The continuous beam shown in the diagram has lengths L=5 m and L2=4 m. The beam is subjected to a un...

A: To Determine Bending moment at the centre of the span AB.

Q: The yoke-and-rod connection is subjected to a tensile force of 5 kN. Determine the average normal st...

Q: An undisturbed sample of soil obtained from field weighed 18 N with a volume of 10-3 m3. The dry uni...

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length ...

Q: Design a tubewell to deliver 33,000 gallons per hour at a depression head of 5 m. The average water ...

Q: A steel rod, circular in cross-section, tapers from 30 mm diameter to 15 mm diameter over a length o...

Concept explainers

Pressure and Stress

Question

complte solution 30 mins left

PROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position shown
if the breaking strength of the horizontal cable attached at C is T kN. Neglect friction.
4
Given:
x = 1 m
$ = 23°
T = 15.5 kN
W =
kN (round off to 2 decimal places)
3.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

6. A simply supported beam carries a concentrated load of 24 kN at 6 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees. ROUND OFF TO FIVE DECIMAL PLACES.
The cross section of a rectangular gate AB of width 2 m is shown in Figure2. The weight of the gate is 1 kN and is hinged along BB. The maximumtensile force that the cable can hold is only 44kN. Calculate the maximumwater depth, y that causes the cable to break and will cause the gate tofail/ open.
What is the slope in a fixed support? Group of answer choices a) undefined b) 1 c) 0 d) 0.5
Consider that the catenary cable in the figure is anchored between supports A and B and issupporting only its own weight, which is w = 50 N/m.Determine the cable length, the minimum pulling force on the cable and the pulling force maximum without cable.
The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. If the tension in cable BE is 204 N and if a = 3m, determine the magnitude of force P(N). Round off only on the final answer expressed in 3 decimal places.
Determine the slope at A in radian. Using Moment Area Method. Let P =38 kN. EI = 14220 kNm^2 Round off the final answer to three decimal places.
A 509.9N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC which lies in a vertical transverse plane and loops underneath the shaft. Calculate the tension T1 (N) in the cable. Round off only on the final answer expressed in 3 decimal places.
A 22-kg ladder with a span of 21 m is resting against a smooth wall at B and the other end rests at A with μs = 0.45. Find the angle of inclination (θ) of the ladder if it is about to slip. Type answer in 2 decimal place.
The power transmission cable in the figure below weighs 165 N/m. Using the table below, write down the numerical value of w. If h= 2.5m, determine the resultant horizontal and vertical forces the cable exert on tower BD.
For the cable loaded as shown. 51. Which of the following gives the value of angle ß₁? a. 36.44° b. 49.78° c. 32.45° d. 52.21° 2. Which of the following gives the tension at BC? a. 35.26 kN b. 32.25 kN c. 26.23 kN d. 20.23 kN 3. Which of the following gives the total length of cable? a. 29.48 m b. 24.26 m c. 20.26 m d. 32.21 m
What is the Vertical component (y-component) reaction force at support C? A. 600N, ( + ) upward B. 200N, (+) upward C. 600N,(-) downward D. 200N,( - ) downward SHOW SOLUTIONS
What is the general moment equation? Section the beam at the rightmost segment of the beam. El = 75,000 kN∙m2