Problem 1: For the following systems with their Open-Loop transfer functions given bellow find steady state errors for unit step, unit ramp, and unit parabolic inputs. What is the system type? U(s) Y(s) GoL (s) 6s +3 Go G (s+3Xs+2), (s+1Xs+5), Go +4s +8) all three parts and handwritten only don't copy

Problem 1: For the following systems with their Open-Loop transfer functions given bellow find steady state errors for unit step, unit ramp, and unit parabolic inputs. What is the system type? U(s) Y(s) GoL (s) 6s +3 Go G (s+3Xs+2), (s+1Xs+5), Go +4s +8) all three parts and handwritten only don't copy

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.16P

See similar textbooks

Similar questions

4. Transfer function of the system is defined as the ratio of Laplace output to Laplace input considering initial conditions________a) 1b) 2c) 0d) infinite 5. Feedback can always reduce the effects of noise and disturbance on system performance? a) Trueb) False 10. For open control system which of the following statements is incorrect?a. Less expensiveb. Recalibration is not required for maintaining the required quality of the output c. Construction is simple and maintenance easyd. Errors are caused by disturbances 11.the closed loop system is.a. Autopilot for an aircraft b. Direct current generator c. Car starter d. Electric switch
For a CT system, given the following set of poles and zeros. poles: sp1=-0.5, sp2=1, sp3=-0.7+j2. Zeros: s1=-2, s2=-0.5. (a) Draw the pole-zero diagram. (b) Does the system stable or not? Justify (c) Find the transfer function H(s) in a rational form.
a)A system has a complex pole pair of (−1 ± 2?) and a real zero of (–3). The steadystate output to a unit step input is 2. Estimate the transfer function of thesystem. b)Using the transfer function derived in a) calculate the followingi) The damping ratio.ii) The undamped natural frequency.iii) The steady state gain.iv) The steady state output.v) The output y(t) using inverse Laplace methods.
Compare the left and right circuit shown below. What is the difference of the two in terms of components? How do you solve the laplace impedance or transfer function of each circuit? Are they the same? What methods must be used on tge left tramsform function?
Simplify given expression using SOP form. K(A,B,C,D) = Σ(0,1,3,7,2,8,10) d(A,B,C,D) = Σ(5,6,11,15)
1. Finding the closed loop transfer function of the system2.What is the steady state error of the system when a unit ramp signal is applied to its input?3. Given Km=5 and Kb=0.01, what should be the K value for a steady-state error to occur at the unit ramp input of the system?
For the system with forward path gain G(s)=s+5s2+3s+2G(s)=s+5s2+3s+2 and feedback gain H(s)=1s+3H(s)=1s+3, input R(s)=8sR(s)=8s will be applied. Find the steady-state error (ess) that will occur in the system and enter it into the space given below
ANSWER THE FOLLOWING Minimize f = m(1,2,3,8,10,13,15) + d(4,6,9,11,12,14) in SOP minimal form.
For a unit step input, a system with forward path transfer function G(s)=20/s2 and feedback path transfer function H(s)=(s+5) has a steady state output of ?
Answer the following question Minimize f = m(1,2,3,8,10,13,15) + d(4,6,9,11,12,14) in SOP minimal form.
Solve All parts or will dislike answer A. Find the open-loop transfer function . Y(S) / R(S)B. Find ?(?) when the input ?(?) is a step function (use expansion of partial fractions).C. State the damping factor ?.D. Indicate whether the system is overdamped, underdamped, or critically damped.E. Indicate the natural frequency of the system ??.F. Indicate the poles and zeros of the system.G. Use the end theorem to find the steady-state value.H. Find ?(?) (use inverse Laplace transform).I. Plot the time response of the system.
Q1) a)A system has a complex pole pair of (−1 ± 2?) and a real zero of (–3). The steadystate output to a unit step input is 2. Estimate the transfer function of thesystem.b)Using the transfer function derived in a) calculate the followingi) The damping ratio.ii) The undamped natural frequency.iii) The steady state gain.iv) The steady state output.v) The output ?(?) using inverse Laplace methods.